1) directly buried bellows type expansion joint
直埋式波纹管补偿器
1.
The classification and characteristics of directly buried bellows type expansion joints are introduced, and discussion is made on the issues to which one should pay attention for the design and installation.
介绍了直埋式波纹管补偿器的分类、特点,讨论了设计安装中应注意的事项。
2) corrugated pipe compensator
波纹管补偿器
1.
Based on the investigation and analysis of the corrugated pipe compensator crack leakage accidents of directly buried heat supply pipeline in power plants,the causes of the accidents are found out and some practical solutions to stress corrosion problems are presented.
通过对热电厂直埋供热管道波纹管补偿器裂纹泄漏事故的调查分析,找出了问题所在,并提出了解决应力腐蚀问题可行的对策。
3) bellows type expansion joint
波纹管补偿器
1.
The calculation of stagnation point position of straight pipeline section with both movable ends and L-type pipeline section with bend at one end and bellows type expansion joint at other end is discussed.
探讨了两侧为活动端的直管段及一侧活动端为弯头,而另一侧活动端为波纹管补偿器的水平转角管段驻点位置的计算。
2.
A test analysis is made on macro-failure and micro-failure characteristics , metallography and corrosion mediums of U-type stainless steel bellows type expansion joints leaked.
对发生泄漏的不锈钢U型波纹管补偿器的宏观失效特征、微观失效特征、金相、腐蚀介质进行试验分析。
3.
This paper presents some information about the design and application of bellows type expansion joint used in heat-supply network,taking Yangquan Power Plant No.
以阳泉第二发电厂新建工程为例 ,介绍了厂区供热管网中波纹管补偿器的设计及应用情况。
4) corrugated expansion joint
波纹管补偿器
1.
The application of corrugated expansion joint in central heating supply;
波纹管补偿器在集中供热中的应用问题
2.
Both a pressure analysis and a blind plate force calculation are made for a corrugated expansion joint in a pressure equilibrium state.
波纹管补偿器在大口径管网中,盲板力在管网固定支架的受力计算中是一个很重要的参数。
5) bellows-type expansion joint
波纹管补偿器
1.
The technical and economic efficiencies of square compensator, bellows-type expansion joint and rotary compensator are compared through an engineering example, and the advantage of rotary compensator is more obvious.
结合工程实例,比较了采用方形补偿器、波纹管补偿器、旋转补偿器的技术经济性,旋转补偿器的优势明显。
2.
By comparing the structural characteristics of bellows-type expansion joint and bellows adjustment device,the selection and application of bellows-type expansion joint and bellows adjustment device in gas industry are discussed.
通过对波纹管补偿器和波纹管调长器结构特点的比较,探讨了燃气行业中波纹管补偿器与波纹管调长器的选择与使用。
6) bellows compensator
波纹补偿器
1.
The author introduces the function, characteristics and classification of the common bellows compensator, explains the calculation of its compensating capacity, application principle in thermal pipeline cascade, its service life and the relevant affecting factors, and discusses how to choose bellows compensator.
主要介绍了常用波纹补偿器的作用、特点、分类,同时介绍了波纹补偿器补偿能力的计算,在热力管道中串联使用的原则,以及波纹补偿器的使用寿命及其影响因素,如何选择和在施工过程中的注意事项、验收规范和预冷紧公式。
补充资料：直管气流式干燥器
分子式：
分子量：
CAS号：
性质：湿料由加料器加入直立管，空气经鼓风机鼓入翅片加热器，加热到一定温度后吹入直立管，在管内的速度决定于湿颗粒的大小和密度，一般大于颗粒的沉降速度（约为10~20米/秒）。已干燥的颗粒被强烈气流带出，送到两个并联的旋风分离器分离出来，经螺旋输送器送出，尾气则经袋式过滤器放空。由于停留时间短，对某些产品往往须采用二级或多级串联流程。
分子量：
CAS号：
性质：湿料由加料器加入直立管，空气经鼓风机鼓入翅片加热器，加热到一定温度后吹入直立管，在管内的速度决定于湿颗粒的大小和密度，一般大于颗粒的沉降速度（约为10~20米/秒）。已干燥的颗粒被强烈气流带出，送到两个并联的旋风分离器分离出来，经螺旋输送器送出，尾气则经袋式过滤器放空。由于停留时间短，对某些产品往往须采用二级或多级串联流程。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条