|
|
1) turbulence intensity profile
湍流强度剖面
2) turbulence intensity profile modeling
湍流强度剖面模拟
3) shear profiler
湍流剖面仪
1.
In the result of lake experiment,the shear profiler shows excellent performance.
文章开发了采集海洋湍流数据的一种新型湍流剖面仪。
2.
Shear profiler is a new ocean instrument based on collection of shear data which can get the data of two millimeter microstructure and focuses hardware of the control system for shear profiler including the design of shear probe amplify circuit , memory circuit based on k9f2808U0C and communication circuit with RS232 protocol .
开发了采集海洋湍流数据的一种新型湍流剖面仪,此仪器可获得海洋垂直剖面2mm尺度的剪切流速度数据,重点研究湍流剖面仪控制系统的硬件设计,包括微尺度流信号放大处理电路,并扩展了FLASH存储器(K9f2808U0C)保存测量结果,及RS232传输协议的数据通信电路设计,湖试结果表明此湍流剖面测量仪性能良好。
4) turbulence intensity
湍流强度
1.
Discusses the differences in turbulence intensity, speed distribution and power spectra between natural and artificial air movement, causes behind the differences and their relations with thermal comfort.
讨论了自然风与机械风的湍流强度、速度分布、频谱参数的不同。
2.
The turbulence intensity near the ground increase dramatically up to 0.
5%的个例可为风力发电带来良好效益,但也有3成的登陆热带气旋将对风电场造成破坏；登陆台风中心附近地层的湍流强度可异常增大达0。
3.
The velocity, turbulence intensity and Reynolds stresses were obtained.
通过速度场、湍流强度、Reynolds应力等物理量的对比分析,表明减阻杆降低了中心涡核区的旋转动能和湍流强度。
5) turbulent intensity
湍流强度
1.
In order to estimate eccentric MR,two parameters named turbulent intensity and regurgitate angle were proposed to modify the effective regurgitate orifice area(EROA) based on traditional PISA algorithm.
针对这一现状,从返流角度和湍流强度两个方面,对传统PISA算法的有效返流瓣口面积(EROA)进行修正。
2.
The compare of heat transfer coefficient distribution,velocity magnitude distribution,radial velocity distribution and turbulent intensity distribution between converging-diverging tube and smooth tube was conducted.
应用数值模拟方法对光滑圆管与缩放管内的空气湍流对流传热在相同条件下进行了计算,对缩放管与光滑圆管内的对流传热系数、速度模量分布、径向速度分布、湍流强度的对比表明:缩放管内空气对流传热系数的提高,是近壁区域流体扰动增强产生了较大的流动径向速度与湍流强度的结果。
3.
The wind speed and the turbulent intensity in the vortical flow area and the pressure distribution on the buildings are analyzed quantitatively.
本文利用计算流体力学(CFD)软件,针对串行排列的三栋建筑物的风环境,采用标准k-ε两方程湍流模型进行了数值模拟,研究分析了三种不同建筑物间的距离下的风涡漩分布特点,并定量分析了涡漩区中的风速和湍流强度,以及建筑物横截面的压力系数分布,为建筑小区的规划最优设计提供理论参考和依据。
6) intensity section
强度剖面
补充资料：关于solidworks 中的剖面线中的剖面线
solidworks的剖面线线型定义和autocad相同,它使用了autocad的剖面线定义方法,与autocad通用.因此,可以对剖面线进行定义. 方法:修改\SolidWorks\lang\chinese-simplified\sldwks.prn 用笔记本打开该文件,添加需要的线形.如 ;; Based on AutoCAD Ver.13.0s Hatch Pattern File ;;;; solidworks 区域剖面线定义文件 :: *金属, (Iron BrickStone), ANSI Iron, Brick, Stone masonry 45, 0,0, 0,.125 *塑料, (Lead Zinc Mg), ANSI Lead, Zinc, Magnesium, Sound/Heat/Elec Insulation 45, 0,0, 0,.125 135, 0,0, 0,.125 *玻璃,AR-GLASS@1.0 45,0,0,0,0.5, 0.5,-0.5 45,0,0.1414214, 0,0.5, 0.3,-0.7 45,0.1414214,0, 0,0.5, 0.3,-0.7 *软木, Cork material@1.0 0, 0,0, 0,.125 135, .0625,-.0625, 0,.35355339, .176776696,-.176776696 135, .09375,-.0625, 0,.35355339, .176776696,-.176776696 135, .125,-.0625, 0,.35355339, .176776696,-.176776696 *无, None 删除不需要的定义类型,可以大大提高solidworks 的启动速度
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条
|