1)  hole detection
空穴检出
2)  Void
空穴
1.
Design method of reinforcement over voids and discussion;
空穴加筋的设计方法及讨论
2.
Furthermore,three ductile damage mechanisms were proposed,which are shear damage without the influence of voids, shear-form void damage and tensile form void damage.
以45中碳钢为研究对象,进行了拉伸、压缩、扭转、精冲实验,并结合有限元对各实验过程中的应力三轴度和延性损伤进行了分析,归纳了金属材料的3种延性损伤机理:无空穴影响剪切损伤、剪切型空穴损伤和拉伸型空穴损伤。
3.
The isolated big void behavior in the tension PM specimen has been ana lyzed by Gurson constitutive model.
讨论了不同位置和不同形状的微空洞对空穴形核、长大及材料的破坏机理的影响。
3)  hole
空穴
1.
Essential Explain on Holes——misunderstanding for the concept of holes in some electronic books can be dearified;
空穴的本质阐释——澄清一些电子学教材对空穴概念的不确切含义
2.
It was concluded that after hole-electron pairs were induced by ultraviolet light,the hole then oxidized methanol directly,forming methanol free radical cation,which would be further oxidized in the .
TiO2受光诱导生成空穴-电子对后,空穴直接氧化甲醇,生成的甲醇正离子在氧气作用下进一步被氧化,形成各种氧化产物。
3.
The hole-blocking characteristics of organic light emitting materials DPVBi were discussed.
讨论了有机发光材料4,4-′b is(2,2-′d iphenyl vinyl)-1,1-′b iphenyl(DPVB i),在结构为ITO/N,N-′b is-(1-naphthyl)-N,N-′d iphenyl-1,1-′b iphenyl-4,4-′d iam ine(NPB)/DPVB i/tris-(8-hydroxyqu inoline)alum inum(A lq3)/L iF/A l的有机电致发光器件中所表现出来的空穴阻挡特性。
4)  cavity
空穴
1.
Insulation effect of the cavity on stress wave;
空穴的绕射隔离效应和对后方应力波的削弱作用
2.
Study on Phenomenon of Negative Air Pressure of Cavity in Interfacial Medium with Tensile Test;
空穴负压现象的界面拉伸试验研究
3.
The relationship between the external load and the cavity radius was determined.
利用Gao Y C给出的一类应变能函数,在有限变形动力学的框架内分析了不可压缩均匀球体突受拉伸恒载作用时空穴的动态生成和分叉问题。
5)  vacancy
空穴
1.
What in discussion is the effect of grain boundary (GB) on the growth of vacancy in crystal.
用分子动力学方法模拟了Σ9对称倾侧晶界铜双晶在拉伸变形过程中晶界对空穴扩展的影响。
6)  cavitation
空穴
1.
Numerical Simulation and Analysis of Two-Phase Flow of Inner Cavitation in Injection Nozzles;
喷油嘴喷孔内部空穴两相流动数值模拟分析
2.
The transient cavitation maps and the simultaneous pressure record.
在搭建的滑动轴承实验台上,对大扰动工况下油膜全景空穴分布图像及油膜压力进行瞬态同步采集,并对图像进行后处理,以便于观察并与基于质量守恒边界条件的理论仿真结果对比,并对同一旋转周期内油膜空穴分布和不同工况下油膜压力进行对比分析。
3.
Numerical techniques with the incompressible mass-conserving cavitation algorithm for steady-state journal bearings have been solved.
采用基于质量守恒边界条件的不可压缩流体空穴算法对稳态工况下滑动轴承进行理论计算,并将计算结果与已有实验结果比较,发现空穴压力的取值对计算结果有影响。
参考词条
补充资料：吹气管液位检出装置
分子式：
CAS号：

性质：检出装置吹气管插入被测容器中，以压缩空气作为能源，用恒压差继动器保持吹气流量恒定。当管口有一定的气泡逸出液面时，管内静压反映液位高度，静压由压力变送器转换成电或气的统一信号由显示仪表显示。可用于敞口容器中有腐蚀性、易结晶或沉淀等的介质液位检测。

说明：补充资料仅用于学习参考，请勿用于其它任何用途。