说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 过热器热力计算
1)  superheater thermodynamic calculation
过热器热力计算
2)  thermal calculation
热力计算
1.
Development and application of thermal calculation software for inter-bin ball mill coal pulverizing system;
钢球磨煤机贮仓式制粉系统热力计算软件
2.
Design and application of general thermal calculation software for boilers of power station;
电站锅炉热力计算通用软件的编制及应用
3.
Heater transfer enhancing and thermal calculation of supercharged boiler steam generator tubes in ships;
船用增压锅炉对流管束热力计算研究
3)  thermodynamic calculation
热力计算
1.
Simplified thermodynamic calculation of surface type air coolers for general conditions;
任意工况下表冷器的热力计算法
2.
Heat transfer study on water-cooled surface air coolers (8): thermodynamic calculation theory and its research review;
水冷式表冷器传热研究(8):热力计算理论及其研究综述
3.
Applied program of thermodynamic calculation and exergy analysis of boilers in power plant;
电站锅炉的热力计算及分析应用程序
4)  heat calculation
热力计算
1.
A universal heat calculation program that is written by Visual Basic Language is used to super high pressure to subcritical pressure coal-fired boilers.
利用VB语言开发了一个可适用于超高压至亚临界参数燃煤锅炉的通用热力计算程序。
2.
The Coal-Water-Mixture(CWM) combustion is a new technology,which is helpful to the energy-saving and safely operation of boilers This paper deduced a formula of heat calculation and testified it The test completes the theory of stoker CWM combustion, promoted its application in boilers als
推导出层燃煤的有限半气化燃烧方法的热力计算公式并加以验证 ,使这一技术从理论上得以完善 ,促进了它在工业锅炉上的推广应用。
3.
The principle is derived by heat calculation on leak conditions that there is a linear relation between some of boiler main working parameters and leakage flow.
通过多个泄漏工况的热力计算结果分析 ,得出大多数锅炉主要运行参数与泄漏量成线性关系的规律 ,并对这些参数变化所提供的泄漏信息可测性进行了简要分析评价。
5)  thermodynamic calculations
热力计算
6)  thermodynamic calculating
热力计算
1.
This paper describes the process to design the program of thermodynamic calculating parameters of triple-effect Lithium/Bromide absorption refrigeration and shows some forms of the program.
对三效溴化锂吸收式制冷循环热力计算程序设计的基本思路和计算方法进行了说明 ,并对该计算程序的功能进行了演
补充资料:动力机械:过热器

锅炉中将蒸汽从饱和温度进一步加热至过热温度的部件﹐又称蒸汽过热器。大部分工业锅炉不装设过热器﹐因为许多工业生产流程和生活设施只需要饱和蒸汽。在电站﹑机车和船用锅炉中﹐为了提高整个蒸汽动力装置的循环热效率﹐一般都装有过热器。采用过热蒸汽可以减少汽轮机排汽中的含水率。过热蒸汽温度的高低取决于锅炉的压力﹑蒸发量﹑钢材的耐高温性能以及燃料与钢材的比价等因素﹐对电站锅炉来说﹐4兆帕的锅炉一般为450℃左右﹔10兆帕以上的锅炉为540~570℃。少数电站锅炉也有采用更高过热汽温的(甚至可达650℃)。


类型和特点 过热器按传热方式可分为对流式﹑辐射式和半辐射式﹔按结构特点可分为蛇形管式﹑屏式﹑墙式和包墙式。它们都由若干根并联管子和进出口集箱组成。管子的外径一般为30~60毫米。对流式过热器最为常用﹐采用蛇形管式。它具有比较密集的管组﹐布置在 450~1000℃烟气温度的烟道中﹐受烟气的横向和纵向冲刷。烟气主要以对流的方式将热量传递给管子﹐也有一部分辐射吸热量。屏式过热器由多片管屏组成﹐布置在炉膛内上部或出口处﹐属于辐射或半辐射式过热器。前者吸收炉膛火焰的辐射热﹐后者还吸收一部分对流热量。在10兆帕以上的电站锅炉中﹐一般都兼用屏式和蛇形管式两种过热器﹐以增加吸热量。敷在炉膛内壁上的墙式过热器为辐射式过热器﹐较少采用。包墙式过热器用在大容量的电站锅炉中构成炉顶和对流烟道的壁面﹐外面敷以绝热材料组成轻型炉墙。图 过热器布置图 为几种过热器的布置。装有过热器的小容量工业锅炉一般只用单级管组的对流式过热器即能满足要求。


性能 锅炉运行工况的变化﹐例如负荷高低﹑燃料变化﹑燃烧工况变动等﹐都对过热器出口汽温有影响﹐所以在电站锅炉中都有调节锅炉出口汽温使其稳定在规定值的手段。常用手段有﹕ 用喷水式或表面式减温器直接调节汽温﹔ 用摆动燃烧器改变炉膛出口烟气温度﹔ 用烟气再循环调节过热器吸热量(见锅炉汽温调节)。锅炉负荷升高时﹐对流式过热器的进出口蒸汽温度升高值增大﹐辐射式过热器的温度升高值减小。若将对流式﹑辐射式和半辐射式过热器合理组合配置﹐则可在负荷﹑燃烧工况等变化时使出口汽温变化较小。过热器管组中各并联管子的吸热量和蒸汽流量在运行中都会有差别。为避免个别管子中温度过高﹐在大型锅炉中把过热器分成若干管组﹐用炉外的集箱对各管组蒸汽进行混合并用导汽管使各管组换位﹐以避免各管间出现过大的温度差。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条