说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 李氏指数(Lipschitz)
1)  Lipschitz-exponent
李氏指数(Lipschitz)
2)  Lipschitz exponent
李氏指数
1.
Lipschitz exponent and its application in simulation of power system transient fault signals analysis;
李氏指数及其在电力系统暂态信号分析中的仿真应用
2.
The method in the paper introduced the concepts of binary wavelet transfer and Lipschitz exponent.
本文使用滤噪方法不同于传统离散小波变换方法 ,而是通过引入二进小波变换和李氏指数的概念 ,根据噪声与有用信号的极大模截然不同的特征 ,实现信号滤噪。
3.
In this paper,through wavelet transform,the Lipschitz exponent and smooth factor analysis of the transient edge of R?R interval,which is induced by rest-to-count experiment,is performed.
利用小波变换表征信号瞬态特征的能力 ,对静卧 -心算实验诱发的R R间期瞬态边沿进行了李氏指数和平滑因子的分析 。
3)  Lipschitz index
Lipschitz指数
1.
Through wavelet coefficient decomposition of energy count rate and further calculation obtaining various Lipschitz index α.
对能量计数率进行小波系数分解,进一步计算得到各尺度的Lipschitz指数α。
2.
Since noise mixing into signal will cause singularity, the size of singularity can be measured by Lipschitz index.
FastICA分离后输出的谐波和噪声信号的幅度发生了变化,本文采用对输入和输出信号归一化的方法很好地解决了这个问题;声带病变和损伤而产生的噪声是一种随机噪声,由于信号中混入噪声后会引起信号的奇异性,奇异性的大小可以用Lipschitz指数来度量。
4)  lipschitz exponent
Lipschitz指数
1.
The relation between Lipschitz exponent of ship magnetic field signal and its velocity;
舰船磁场信号的Lipschitz指数与船速的关系
2.
The singularity can be determined by the local modular maximum line and its Lipschitz exponent,which can be obtained through the multi-scale complex continuous wavelet decomposition.
通过对基桩检测信号进行多尺度一维连续复小波分解,得到局部模极大值线(local maxi-mum line),计算模极大值线对应位置的Lipschitz指数值,从而综合判断信号的奇异点位置。
3.
This paper put forward a method to make use of Lipschitz exponent of differential pressure fluctuation signa.
该文提出了利用压差波动信号的Lipschitz指数来识别流型的方法。
5)  Lipschitz exponents
Lipschitz指数
6)  Lipschitz α
Lipschitz指数α
1.
Based on the feature that signal singular points often appear at the boundary and its singularity is described by Lipschitz α, wavelet transform,because of its automatic zooming property , is applied to signal analysis to detect signal singular points and calculate the singularity degree Lipschitz a at the same time.
根据测量信号在边界处具有奇异点这一特点,以Lipschitz指数α定量刻划信号在奇异点处的奇异程度,利用小波分析的“变焦距”特性分析测量信号,确定奇异点的位置并计算相应的奇异度Lipschitz指数α,最后将α值相等或相近的奇异点顺序连接作为边界。
补充资料:迁移效率指数、偏好指数和差别指数


迁移效率指数、偏好指数和差别指数


迁移效率指数、偏好指数和差别指数迁移效率指数是用于测定两地间人口迁移效率的指标。它是净迁移对总迁移之比。计算公式为:EIM一摇寿纂拼又‘。。上式中,}人么夕一材方}为i、]两地净迁移人数;从少+材户为i、]两地总迁移人数;El入了为迁移效率指数。 EIM的取值范围为。至100,如某一地区的值越大,反映迁移的的影响也越大。如果计算i地区与其他一切地区之间的人口迁移效率指数EIM厂,则: }艺材。一芝Mj、}EIM汀艺。+乏M,(j笋i) 迁移偏好指数是从一个地区向另一地区的实际迁移人数与期望迁移人数之比。计算公式为:____M.___材尸2行一:一二子一一不石一二,么M“ 了厂‘.厂‘、八 }二不十二六二1 、厂厂7上式中,M“为从i地迁到j地的实际迁移量;艺材。为总的人口迁移量;尸为总人口;M尸I,j为迁移偏好指数。通过计算迁移偏好指数,可以反映各地区的相对引力。 迁移差别指数是反映具有某种特征的迁移人口与非迁移人口区别的指数。例如,专业技术人员的人数所占比重,各种文化程度人数所占比重等,以便研究人才流失和其他间题。计算公式为:M‘从IMD、一翌不丝xl。。 .义V‘ N上式中,M为迁移人数;M,为具有i特征的迁移人数;N为非迁移人数;N‘为具有i特征的非迁移人数;了八了D、为迁移差别指数。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条