说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 点铰支座
1)  point-hinge bearing
点铰支座
2)  hinge pedestal
铰链支座
1.
The technological property of the hinge pedestal part is analyzed.
分析了铰链支座的工艺性 ,详细介绍了级进模排样方案和总体结构 ,阐述了关键部件的设计计算方法。
3)  spheric joint support
球铰支座
1.
The slip spheric joint support is also used for the large-span steel structure roofing in order to dispel distortion by temperature change an.
为了消除温度变形和安装允许误差的影响,对大跨度钢结构屋面在支座部位采用了滑动球铰支座。
4)  articulated gate shoe
支铰座
1.
In light of high manufacturing technical requirements and structural characters of steel mould trolley, the author introduces the manufacturing technologies of its main parts as bogie frame, traction mechanism and formwork, and proposes welding elements of articulated gate shoe, in order to improve manufacturing level of steel mould trolley and to popularize its application.
针对钢模台车的制作技术要求高及结构特点,介绍了台车架、行走机构、模板等钢模衬砌台车主要部件的制作工艺,提出了支铰座的焊接要点,最终提高钢模台车制作水平,推广其应用范围。
5)  hinge support
铰支座
1.
In this article, authors introduce some construction technologies of prestressed anchor bolts of wide diameter pin roll hinge supports of the steel structure engineering of Shenzhen Meeting and Exhibition Center such as fix position and prebury, tension and grouting methods of anchor bolts, installation and gap control methods of D600 pin roll hinge supports and so on.
介绍深圳会展中心钢结构工程中大直径销轴铰支座预应力锚栓的定位预埋、锚栓的张拉灌浆工艺、D600销轴铰支座的安装与间隙控制等施工技术。
6)  single hinge bearing
单铰支座
补充资料:闭式单点、双点压力机
代码:00413
设备名称:闭式单点、双点压力机
型号规格:公称力≥800kN
计量单位:台
主要参数内容
国际先进国内先进国内一般国内落后评定方法及说明
(一)加工精度
    参照GB10924-89、GB10933-89、JB5200-91
1、滑块下平面对工作台上平面的平行度(mm)
30%精度储备20%精度储备达到规定值大于规定值 
0.02+0.10/100×滑块下平面的被测长度
     
2、滑块行程对工作台上平面的垂直度
30%精度储备20%精度储备达到规定值大于规定值 
0.05+0.02/100×滑块行程长度
     
(二)结构性能
     
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50%
大于规定值10%大于规定值达到规定值达不到规定值 
2、液压超负荷保险装置、微调装置、吨位指示器
全部具有全部具有部分具有没有 
(三)噪声dB(A)
     
1、公称力≤400kN
≤85≤87≤88>88 
2、公称力>400kN
≤87≤88≤90>90 
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条