1) brook streaming phase pneumatic handling
溪流相气力输送
2) plug pneumatic conveying
密相栓流气力输送
1.
Effect of air-knife operation condition on plug pneumatic conveying;
气刀操作条件对密相栓流气力输送的影响
3) dense phase pneumatic conveying
浓相气力输送
1.
Optimization design method of stepped pipeline in dense phase pneumatic conveying;
浓相气力输送中变径管道优化设计方法的研究
2.
Under the experimental conditions, the coal ash was transported by compressed air in the horizontal and vertical pipe of 80mm inner diameter and 210m length, at the state of high press, low speed, dense phase pneumatic conveying.
在内径为 80mm、长为 2 10m的水平和垂直输送管道中进行了高压流态化浓相气力输送粉煤灰的实验研究。
4) dense phase pneumatic conveying
密相气力输送
1.
Material flow state in dense phase pneumatic conveying process and selection of the feeding device;
密相气力输送物料流动状态分析及供料装置的选用
2.
Application of RBF neural network in dense phase pneumatic conveying system;
径向基网络在密相气力输送中的应用
3.
Solid mass rate at different gas flow is forecasted by using improved BP neural network in dense phase pneumatic conveying.
在水平管道中 ,用压缩空气和氢气对煤粉和小米进行密相气力输送实验 ,利用改进的 BP神经网络对不同气量下的固体质量流率进行了预测。
5) dense-phase pneumatic conveying
密相气力输送
1.
The prediction of pipe pressure drop in powder dense-phase pneumatic conveying;
粉体密相气力输送中的管道压降预测
2.
Experiments of dense-phase pneumatic conveying for pulverized coal with different mean particle size were carried out on the test rig of high pressure dense-phase pneumatic conveying.
在高压密相气力输送试验台上,进行了不同平均粒径煤粉的密相输送试验。
3.
Experiments of dense-phase pneumatic conveying of pulverized coal with different mean particle size using nitrogen were carried out in an experimental test facility with the conveying pressure up to 4 MPa.
研究表明,相同质量流量下,平均粒径大的煤粉在弯管中的压损要高于平均粒径小的煤粉;在密相气力输送中,压损随表观气速的降低而增加。
6) dilute phase pneumatic conveying
稀相气力输送
1.
Application of steel-alumina ceramics composite pipe for dilute phase pneumatic conveying;
氧化铝陶瓷内衬复合钢管在稀相气力输送中的应用
补充资料：脉冲式气力输送
分子式：
CAS号：
性质：是高压、低速及密相的气力输送装置。可降低能耗，减少物料破碎和管道的磨损。适合输送黏性的粉状及粗糙的粒状物料。一般密相输送速度为7～15m/s左右，脉冲密相输送速度为1m/s或更低的速度。由发送器、粒位器、气刀及控制盘等构成。气刀将压缩空气间歇脉冲地通入输送管道，并把发送器排出的物料柱分割成间断料栓，借料栓前后的静压差，推动物料向前输送。
CAS号：
性质：是高压、低速及密相的气力输送装置。可降低能耗，减少物料破碎和管道的磨损。适合输送黏性的粉状及粗糙的粒状物料。一般密相输送速度为7～15m/s左右，脉冲密相输送速度为1m/s或更低的速度。由发送器、粒位器、气刀及控制盘等构成。气刀将压缩空气间歇脉冲地通入输送管道，并把发送器排出的物料柱分割成间断料栓，借料栓前后的静压差，推动物料向前输送。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条