1) composite fuel oil
复合油相
1.
When antifreezing agent is added into composite fuel oil, the freezing point of composite fuel oil can be reduced.
在分析岩石膨化硝铵炸药组成的基础上,提出了通过添加抗冻剂来降低复合油相的凝固点是制备耐冻膨化硝铵炸药的有效方法和技术途径。
2.
In this paper,components of composite fuel oil against agglomeration and production technique and its main factors of a big bundle of AN TNT are discussed with details.
详细讨论了铵锑炸药防结块复合油相材料组成及铵锑大包的生产工艺及主要工艺参
3.
Composite fuel oil of different formula how to affect the performance of Modified ANFO(1) Adding different content of mineral wax and rosin to the composite wax and paraffin,and to study mineral wax and rosin how to affect the performance of Modified ANFO.
本文重点研究了不同配方的复合油相以及添加剂XJ-1和Al粉对改性铵油炸药性能的影响,同时对改性铵油炸药的生产工艺进行了优化设计,并建立了改性铵油炸药配方的数学模型,编制了专门的计算程序进行了线性规划求解。
2) complex oil phase material
复合油相材料
1.
In this paper, based on the experiment and theoretical analysis,the influence extent and affect mechanism of complex oil phase material on the various performances of emulsion explosives are described.
文章通过实验和理论分析 ,系统地阐明了复合油相材料的物化性质对乳化炸药各种性能的影响程度和作用机理。
3) composite reservoir
复合油藏
1.
Pressure transient analysis of composite reservoir using the boundary element method;
任意形状复合油藏压力动态的边界元分析
2.
Productivity analysis of fractured wells in two-area composite reservoir by finite element method;
复合油藏压裂井产能的有限元分析
3.
This paper proposes mathematic model for well test analysis of perfectly describing the composite reservoir with the bottom-hole storage and the skin effects and the three kinds of outer boundary conditions(infinite boundary,constant pressure outer boundary and closed boundary).
针对复合油藏,建立了考虑井筒储集和表皮效应和三种外边界(无穷大、定压、封闭)条件下的试井分析模型;利用Laplace变换,在Laplace空间中得到了储层压力和井底压力分布的精确解;经全面和深入的分析,发现了描述该类油藏在三种外边界条件下的渗流特征的解式之间具有的相似结构,并作了进一步的讨论。
4) compound reservoir
复合油藏
1.
Aimed at Gravity Override in a steam- injection processes, a well test analysis model of wedge - shaped compound reservoir is set up to simulate to slant steam front.
针对蒸汽驱中的重力超覆现象,提出采用楔状复合油藏模型来模拟倾斜蒸汽前缘建立考虑热损失的数学模型,通过拉普拉斯变换,得到两区复合油藏井底压力在拉氏空间的解。
2.
The compound reservoir model is used abroad in testing data interpreted.
实践表明,流体在复合油藏交接面间的流动存在着一定的附加阻力,尤其是渗透率低于5×10-3μm2的油藏,这种附加阻力的影响表现得更加明显。
3.
For the thermal recovery well test with steam injection,the compound reservoir model should be used to replace the actual reservoir,at the same time the heat losses to the surrounding formation must be considered.
对于注蒸汽热采试井必须采用复合油藏模型来代表实际油藏 ,同时还要考虑蒸汽在地层中的热损失。
5) complex reservoir
复合油藏
1.
New calculation method of Fetkovich production - time standard curve for complex reservoir;
复合油藏Fetkovich产量-时间标准曲线计算的新方法
6) composite reservoirs
复合油藏
1.
Study of pressure-transient characteristic for triple-medium composite reservoirs;
三重介质复合油藏压力动态特征研究
2.
The flow model of the triple-medium composite reservoirs and the type curves;
三孔均质径向复合油藏模型与试井样版曲线
补充资料:皂化溶解油、肥皂油和调水油
分子式:
CAS号:
性质:又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂(如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂)和少量稳定剂(如乙醇或甲醇)而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主,润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
CAS号:
性质:又称皂化溶解油、肥皂油和调水油。金属切削油的一类。一般是淡褐色至深褐以液体或半固体。由在矿物油中加入适量的皂类乳化剂(如钠皂、钾皂、松香钠皂、松香皂或环烷酸钠皂)和少量稳定剂(如乙醇或甲醇)而成。使用时与软水掺合成稳定的白色乳化液。作用以冷却为主,润滑为次。用于车制、锯断、钻孔、磨制等金属粗加工。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条