1) pressuremeter modulus
旁压模量
2) modulus of pressuremeter
旁压仪模量
3) septate mode
旁模
4) compressive modulus
压缩模量
1.
Calculation of compressive modulus of grid structure -composite foundation;
格栅状复合地基压缩模量的计算
2.
Value determination problem of compressive modulus E_s of soil layers ⑦,⑧ and ⑨ in Shanghai soft soil foundation;
论上海软土地基⑦⑧⑨层压缩模量E_s的定值问题
3.
It was found that gelatin coatings were formed on the pore walls of porous scaffold samples successfully without destroying their porous characteristic,but these coatings improved the compressive strength and compressive modulus o.
复合明胶涂层提高了样品的压缩强度和压缩模量,与未涂覆样品相比,涂敷样品受压时的应变特性发生了明显变化。
5) compression modulus
压缩模量
1.
Test research on compression modulus of sandy soil tunnel surrounding rock;
砂类土体隧道围岩压缩模量的试验研究
2.
The response to electric field of the composite systems was studied by measure of compression modulus of the elastomers and dynamic-exam of resistance in the cure .
通过对弹性胶体压缩模量的测试和胶凝过程中电阻的动态监测,研究了胶体体系对电场的响应行为。
6) compressibility modulus
压缩模量
1.
The compressibility modulus of the dewatering subsidence,sE,is mainly determined by the character diameter of the sand,20D,and the ef.
疏水沉降的侧限压缩模量sE受特征粒径20D和水压降hD控制,20D,hD越大,sE越大;当土样不变时,sE与hD呈正相关关系;当hD一定时,土体的细颗粒含量越多,20D越小,则侧限压缩模量sE越小,土体变形量越大。
2.
Based on settlement data measured in field,compressibility modulus and consolidation coefficient of soil layers are obtained by back analysis method.
基于沉降实测资料,采用反分析方法,确定了各土层的压缩模量和固结系数,并将反演得到的参数代入太沙基一维固结方程,对后续沉降进行预测,从而确定分级压载的下一级压载时间与压载量。
补充资料：橡胶模具、橡胶压模、橡胶硫化模
分子式：
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
CAS号：
性质：又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得，并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同，型腔尺寸必须考虑不同橡胶的收缩率，在产品尺寸基础上进行放大或缩小，方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条