1) out-of-plane thermal conductivity
法向热导率
1.
The nonequilibrium molecular dynamics method is adopted to study the out-of-plane thermal conductivity of single crystal silicon films at nanoscale.
44nm的单晶硅薄膜的法向热导率,模拟结果表明,薄膜热导率低于同温度下单晶硅的实验值,存在显著的尺寸效应,当膜厚度在20nm以下时,法向热导率随尺度减小而线性减小,当膜厚度大于20nm时法向热导率随尺度呈现二阶多项式变化。
2) lateral thermal conductivity
横向热传导性,横向热导率
3) axial heat conduction
轴向导热
1.
Effect of axial heat conduction on heat transfer in micro-channels;
轴向导热对微通道内传热特性的影响
2.
With the further simplified conditions, the effect of an axial heat conduction on heat transfer to liquid sodium in thermal entrance region .
从一般控制方程出发,根据环管热进口段传热特点,结合优化选择影响传热的诸如速度分布、湍流热量扩散率和动量扩散率等半经验关系式,建立能借助计算机理论求解的计算模型,并在进一步简化条件下计算、分析了轴向导热对进口段传热的影响。
3.
The axial distribution of the film thickness and meniscus of liquid, the axial profile of the pressures of liquid and vapor and the capillary radius of the liquidvapor interface, the frictional interaction at the liquidvapor interface and the axial heat conduction of the wall .
对热管内部的流动和传热传质过程建立模型,分析槽道中液体厚度和弯月面的轴向分布,液体和蒸汽的压力、汽 液界面弯月面半径的轴向变化、汽 液界面流动的相互作用以及管壁的轴向导热,通过计算得到热管的外壁面温度分布和传热性能。
5) thermal conductivity
热导率
1.
Effect of Si on the microstructure and thermal conductivity of pressureless infiltrated SiC_p/Al composites;
Si对无压浸渗SiC_p/Al复合材料显微组织与热导率的影响
2.
Effect of preparation condition on the thermal conductivity of xonotlite-silica aerogel nanoporous super insulation materials;
制备条件对硅酸钙复合纳米孔超级绝热材料热导率的影响
3.
Influence of substrate thermal conductivity on the phase composition of high velocity oxy-fuel sprayed Al-Cu-Cr quasicrystalline coatings;
基体热导率对超音速火焰喷涂Al-Cu-Cr准晶涂层相组成的影响
6) heat conductivity
热导率
1.
Research on high precision fast detection system for sea sediment heat conductivity;
海洋沉积物热导率高精度快速测量系统研究
2.
The effect of pressure in the experiment measuring heat conductivity of air;
对测量气体热导率实验中压强影响的分析
3.
An application of the theory of thermal wave: dynamic measure of the heat conductivity of a good thermal conductor;
热波理论的应用——良导热体热导率的动态法测量
补充资料:各向同性和各向异性
物理性质可以在不同的方向进行测量。如果各个方向的测量结果是相同的,说明其物理性质与取向无关,就称为各向同性。如果物理性质和取向密切相关,不同取向的测量结果迥异,就称为各向异性。造成这种差别的内在因素是材料结构的对称性。在气体、液体或非晶态固体中,原子排列是混乱的,因而就各个方向而言,统计结果是等同的,所以其物理性质必然是各向同性的。而晶体中原子具有规则排列,结构上等同的方向只限于晶体对称性所决定的某些特定方向。所以一般而言,物理性质是各向异性的。例如, α-铁的磁化难易方向如图所示。铝的弹性模量E沿[111]最大(7700kgf/mm2),沿[100]最小(6400kgf/mm2)。对称性较低的晶体(如水晶、方解石)沿空间不同方向有不同的折射率。而非晶体(过冷液体),其折射率和弹性模量则是各向同性的。晶体的对称性很高时,某些物理性质(例如电导率等)会转变成各向同性。当物体是由许多位向紊乱无章的小单晶组成时,其表观物理性质是各向同性的。一般合金的强度就利用了这一点。倘若由于特殊加工使多晶体中的小单晶沿特定位向排列(例如金属的形变"织构"、定向生长的两相晶体混合物等),则虽然是多晶体其性能也会呈现各向异性。硅钢片就是这种性质的具体应用。
介于液体和固体之间的液晶,有的虽然分子的位置是无序的,但分子取向却是有序的。这样,它的物理性质也具有了各向异性。
介于液体和固体之间的液晶,有的虽然分子的位置是无序的,但分子取向却是有序的。这样,它的物理性质也具有了各向异性。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条