1) turning point
转向点
1.
Higher-order asymptotic solutions of a class of boundary value problems for third-order differential equation with a turning point;
一类具有转向点的三阶微分方程的边值问题的解的高阶渐近展开
2.
On nonlinear differential equation with turning point involving two small parameters;
具有两小参数的转向点的非线性微分方程
3.
Singulary perturbed equations with turning point;
具有转向点的奇摄动方程
2) turning points
转向点
1.
In this paper,we study the singular perturbation of Robin problems for second order nonlinear systems with turning points.
通过研究一类具有转向点的二阶非线性系统Rob in边值问题的奇摄动。
2.
In this paper, a uniform numerical solution of the elliptic equation singular perturbation problem with two directions of turning points is considered.
讨论具有双向转向点的椭圆型方程奇摄动问题的一致数值解法,证明带指数型拟合因子的差分格式关于小参数ε的一致收敛结果。
3.
In this paper the existence of solutions of a class of singularly perturbations of third order boundary value problems with turning points is proved,and the uniformly valid estimates of the solutions are given.
本文证明了一类具有转向点的三阶奇摄动边值问题解的存在性,并给出了解的一致有效估计。
3) steering feature
转向特点
1.
The steering features of four-wheel steering automobile are comparatively analyzed in this paper.
本文分析比较了四轮转向汽车的转向特点 ,概述了电控四轮转向汽车的结构原理 ,介绍了四轮转向系统的控制策略 ,指出了四轮转向系统控制技术所面临的困难 ,并展望其发展趋势。
4) spot turn
定点转向
5) Turning point singularity
转向点奇异
6) neutral steering point
中性转向点
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条