1) stress classification method
应力分类法
1.
In this paper, the stress classification method and plasticity analysis method used in analytical design of pressure vessel were stated.
对压力容器分析设计的应力分类法与塑性分析法做了概述,并对它们各自存在的问题进行了扼要的介绍。
2.
The intensity evaluation was completed by the stress classification method.
应用ANSYS软件分别建立了某裂解老区第二急冷锅炉的轴对称温度分析模型和空间非线性结构分析模型,对其进行温度分析和应力分析,并采用应力分类法完成强度评定。
3.
Recent advances of the stress classification method are introduced in this paper.
以ASMEⅧ-2 2007版为主线介绍应力分类法的最新进展,并结合我国JB 4732标准和欧盟标准EN 13445 2002来进行讨论和评述。
2) stress elassification method
应力分类方法
3) stress classification
应力分类
1.
Comparison Between the Stress Classification and the Reinforcement Design Methods at the Opening Nozzles of a Pressure Vessel;
压力容器开孔接管处的应力分类及补强设计方法的比较
2.
The state of complicated stress was analyzed and suggestions for assessing the stress classification of the finite element analysis result of the large openings were put forward.
针对内压容器壳体在开孔部位尤其大开孔接管部位有很大的应力集中现象,从应力分类的基本原理出发,分析了开孔边缘的复杂应力状态,并对大开孔有限元应力分析结果的应力分类评定提出建议。
3.
The elastic "Design by Analysis" methods focus on stress classification approaches,such as the Stress Equivalent Linearization,the Two-Step Approach,the Primary Structure method,the Elastic Compensation method,and the GLOSS R-Node method.
基于弹塑性理论的分析设计方法回避了弹性方法中应力分类法的实现难点等局限性,并已被编入欧盟的设计标准和美国的A SM E规范。
4) gravitation classification
引力分类法
1.
This paper is inspired by the mind of universal gravitation and the method of "gravitation classification" is introduced here.
本文从物理学中的万有引力得到启发 ,提出了“引力分类法”。
5) stress calculus of variations
应力变分法
1.
Analysis of stress distribution near borehole in orthotropic rockmass with stress calculus of variations;
正交各向异性岩体钻孔周围应力分布的应力变分法分析
6) stress analysis method
应力分析法
1.
Modeled the reliability of the controller of self-rescue system for AUV,predicted the failure rate λ_s and mean time between failure MTBF by using part stress analysis method,and finally raised several ways to improve the reliability of system.
针对智能水下机器人自救系统的控制器部分建立了其可靠性数学模型,应用元件应力分析法,预计出了自救系统控制器部分的故障率λs及平均故障间隔时间MTBF,并总结了若干提高系统可靠性的途径。
2.
According to the practical issues encountered in boiler inspection the stress analysis method is applied in analytic error calculation of small end of conical head with half top angle>60°.
针对在锅炉检验中常遇到的实际问题 ,应用应力分析法 ,对半顶角大于 60°锥形封头的小端解析误差进行了计算分析 ,并经解析式验算 ,指出其误差在工程允许范围内。
3.
In the paper, the reliability of a module was predicted with device counting method and device stress analysis method repectively.
该文以一个模块为例,分别用元器件计数法和应力分析法进行可靠性预计,从中比较出两种算法的特点,以便更好的适应设计。
补充资料：轧辊残余应力(见轧辊应力)
轧辊残余应力(见轧辊应力)
residual stresses in roll
zhagun eanyu yingli轧辊残余应力(residual stresses in roll)见礼辐应力。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条