1) JQ160-50 bridge building machine
JQ160-50架桥机
1.
Research and manufacture of JQ160-50 bridge building machine;
JQ160-50架桥机的研制
2) bind-mechanism
架桥机理
3) bridge erector
架桥机
1.
In the construction of the north-bank approach of the Tianxingzhou Bridge of the passengers-oriented railway line,because of the limitation of the work clearance of the big gantry crane and the deck operation scale,Type-HZQ900 bridge erectors can not be assembled in place at one stroke.
在武汉天兴洲大桥北岸引桥客运专线桥梁施工中,由于提梁大龙门吊机作业空间及桥面安装工作面规模的限制,HZQ900型架桥机不能一次性原位安装就位,结合本工程的实际情况,以及考虑未来可能的架桥机应用工况,并统筹考虑安全、技术经济分析等因素,采用垂直连续顶升技术成功在高位完成架桥机的安装工作,介绍了高位安装的原理、工作流程及关键技术,为类似架桥机高位拼装积累了宝贵的经验。
2.
Taking assembled continuous twin-guiding-beam as its structural form,Type-SPJ900/32 bridge erector is safe and reliable , its construction procedure being concise as well.
SPJ900/32架桥机采用拼装式连续双导梁的结构形式,作业程序简捷,安全可靠。
4) bridge erecting machine
架桥机
1.
Project study of 800t bridge erecting machine with box beam for Beijing-Shanghai high speed dual line railway;
京沪高速铁路双线箱梁800t级架桥机方案研究
2.
Stability analysis and calculation of frame beam for bridge erecting machine JQ600 with box cross section beam;
JQ600型箱梁架桥机架梁稳定性分析计算
3.
Influence of temperature load on railway bridge erecting machine s strength;
温度载荷对铁路架桥机的强度影响
5) bridge girder erection machine
架桥机
1.
This paper presents the structure of bridge girder erection machine and the assembly of prefabricated sections.
本文介绍节段拼装架桥机的构造以及预制节段梁拼装施工等内容。
2.
Because the Xizhi River Bridge is a 35 m flitch T beam with 15° skew angle, the traditional orthogonal bridge girder erection machine must be reformed to adapt to oblique erecting beam construction.
由于西枝江大桥为 15°角斜交的 35m组合T梁 ,故务必将传统正交架桥机加以技术改造 ,以适应 90t级 35m斜交架梁施工。
3.
Structural overall design of a newly developed railway bridge girder erection machine that is of simply-supported single beam and is transversely movable above ground in China is introduced, and computer simulation analysis of basic conditions of the bridge girder erection machine in service is provided as well.
介绍了我国一种新型单梁简支空中横移式铁路架桥机的总体结构设计及其架桥过程结构总体状况的计算机仿真分
6) overhead launching gantry
架桥机
1.
In this paper,the design alternatives,principal components and construction sequences of the TP75 overhead launching gantry used for the segmental assembling of the bridges are described.
介绍TP75节段拼装架桥机在该工程中的设计方案、主要部件及施工步骤。
2.
This paper deals with the construction of lifting and installation of the north main cable saddles of Wuhan Yangluo Changjiang River Highway Bridge by the lifting support made up of the main girder and hoisting trolley of overhead launching gantry.
介绍武汉阳逻长江公路大桥北主索鞍采用架桥机主梁和起重台车等组成的安装吊架进行吊装施工的情况。
3.
In this paper,the working principles,principal technical parameters,performance and different construction schemes of the JQ900 overhead launching gantry with lower launching nose are dealt with.
介绍JQ900型下导梁架桥机工作原理、主要技术参数、性能及各项施工方案。
补充资料：JQ、QG系列气流干燥机
  型号规格
| ||||||||||||||||||||||||||||||||||||||||||||||||||||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条