说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 湿喷工艺
1)  wet-spurting technology
湿喷工艺
1.
This article introduced the application of wet-spurting technolo gy in Modaoxi Tunnel in Chongqing Yuhe Speedway, and summarized the construction measu re and the construction matters needing attention of the wet-spurting technology according to actual situation in Modaoxi Tunnel.
本文介绍了湿喷技术在重庆市渝合高速公路磨刀溪隧道中的应用,并根据磨刀溪隧道的实际情况总结出湿喷工艺的施工方法和施工措施以及施工中的注意事项。
2)  wet-on-wet
湿碰湿工艺
3)  rewetting process
回湿工艺
1.
It was discussed that the rewetting process and its effects on wet-blue before retanning in this paper.
对复鞣前蓝湿革回湿工艺及其回湿效果进行了研究和探讨。
4)  wet process
湿法工艺
1.
After studing the entire iron contents and component of the sulphurous iron ore residue,this program use wet process and take the sulphurous iron ore residue as raw material to prepare iron oxide red,omiting the step using the special use reducer to restore.
在对硫铁矿烧渣全铁含量以及组分研究的基础上,运用湿法工艺以硫铁矿烧渣为原料制备铁红,省去专用还原剂还原的步骤,研究了高温硫酸还原的最佳条件,试验确定制备铁红的简易工艺,节省了试剂与能源。
2.
Traditional wet process of producing hydroxypropyl starch and the dry process used in this factory are described briefly.
简述了传统羟丙基淀粉的湿法工艺和本厂的干法工艺,着重介绍了已工业化生产的绝干法工艺,并对其工艺原理进行了初步探讨。
3.
The application of wet process is described in the preparation of lithium ion battery materials including anode and cathode material, diaphragm electrode, electrolyte, diaphragm material.
介绍了湿法工艺在锂离子电池材料 (包括正极材料、负极材料、膜电极、电解液、隔膜材料 )制备的应用 ,指出湿法工艺是锂离子电池材料制备的重要方
5)  wet-scenting process
湿窨工艺
1.
The contents of cis-3-hexenyl acetate,linalool,methyl anthranilate,cadinene,indole,benzyl alcohol,nerolidol,geranyl acetate were significantly increased in the jasmine scented tea made by wet-scenting process.
采用湿窨工艺窨制茉莉花茶,苯甲酸顺-3-己烯酯、芳樟醇、邻氨基苯甲酸甲酯、杜松萜烯、吲哚、苯甲醇、橙花叔醇、乙酸香叶酯等成分的含量显著提高;配花量在69%~115%之间,配花量递增,茉莉花茶香气成分的含量亦随之增加,当配花量达到96%以上,茉莉花茶的主要香气成分含量差异不显著,表明茶坯的吸香已趋于饱和。
6)  wet spinning process
湿纺工艺
1.
The application of high shearing pump in two step acrylon wet spinning process;
高剪切泵在腈纶二步法湿纺工艺中的应用
补充资料:湿碰湿工艺
分子式:
CAS号:

性质:喷涂的第一道漆膜还没有实干时接着就喷涂第二道,这种喷涂工艺叫做“湿碰湿”。是一种节约能源、减少工序的方法,但并不适用于所有的涂料。有的涂料会流坠、起皱纹,影响漆膜干燥。适于湿碰湿的漆种有氨基漆、过氯乙烯和聚氨酯漆、环氧基漆。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条