1) tooth thickness allowance
齿厚允许偏差
1.
This paper introduces a method and some corresponding software for calculating tooth thickness allowance in involute cylindrical gears,based on ISO1328 1990 s International Standards for Gear Accuracy.
介绍了基于ISO1328九十年代国际齿轮精度标准的渐开线圆柱齿轮齿厚允许偏差的计算方法和为此编制的电脑软件,该方法对推动齿轮新老标准的转换具有较高的实用价值,可供生产、经销和使用齿轮的企业参考或选用。
2) allowable deviation
允许偏差
1.
A discussion for defines bounds of allowable deviation of construction works in site;
关于确定施工过程允许偏差范围的讨论
2.
In combination with engineering practice, statistics and analyses are carried out to the installation deviation of cylinders in bed-seated cylindrical breakwater engineering and suggestions on determination of the allowable deviation are proposed.
结合工程实例 ,对坐床式圆筒防波堤工程的圆筒安装偏差进行了统计、分析 ,并对其允许偏差值的确定提出建
3) allowable variation
允许偏差
1.
The allowable variation of cover depth to the steel in reinforced concrete is of significant influence upon the durability of reinforced concrete for maritime works.
允许偏差钢筋混凝土保护层厚度的对水运工程钢筋混凝土耐久性有着重要影响,实施保护层厚度的实体检测对水运工程而言是新生事物,合理确定实体检测保护层厚度的允差,对顺利及正确地开展水运工程实体检测保护层厚度是很必要的,势必促进水运工程混凝土结构耐久性质量的提高。
2.
The paper presents a study and discussions on the determination of the allowable variation in the thickness of concrete cover to reinforcement so as to rationally and effectively control the allowable variation in construction of concrete cover to improve the useful life of concrete structures fo.
文中对混凝土保护层厚度施工允许偏差的确定进行了研究和讨论,以合理有效地控制混凝土保护层厚度施工允许偏差,提高水运工程混凝土结构使用寿命。
3.
It gives a brief introduction to the method of pile collision calculation by Excel software (electronic form) and correction of pile position parameters when considering the in fluence of piling allowable variation during construction of pile foundation for high－ piled wharf.
简要介绍在高桩码头桩基工程施工中，当考虑沉桩允许偏差影响时，利用 Excel软件 (电子表格 )进行碰桩验算及修正桩位参数的方法。
4) permissible variation
允许偏差
1.
The development of standards of permissible variations in chemical composition of superalloy products is introduced, the scope of different standards are compared.
概括国内外高温合金化学成分允许偏差标准现状,对比中外标准的适用范围；阐述 GJB 5307规定的24种元素的允许偏差要求及其依据,着重分析 Fe、Al、Ti、C 元素的偏差要求；指出 GJB 5307的适用性。
5) permitted error
允许偏(误)差
6) permissible angular misalignment
允许角偏差
补充资料：齿（齿所）
齿（齿所）
齿（齿所） 病名。系指牙齿被醋浸渍的病证。《诸病源候论》卷二十九：“齿（齿所），齿伤酢也。齿者骨之所终，髓之所养，髓弱骨虚，风气客之，则齿（齿所）。”酢，同醋。参见齿齼条。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条