1) pipe pressure
管道压力
1.
Relation between venting speed and pipe pressure, water moving speed and pipe pressure;
有压管道中排气速度与管道压力的关系
2) pressure pipeline
压力管道
1.
Magnetic memory testing on welding line of pressure pipeline;
压力管道焊缝的磁记忆检测
2.
The fatigue life computation method of pressure pipeline containing defects based on reliability assessment;
基于可靠性评价的含缺陷核压力管道疲劳寿命预测方法
3.
Welding for large-scale pressure pipeline of HS610U-M;
HS610U-M高强钢大型压力管道的焊接
3) pressure pipe
压力管道
1.
Development of Modularized Design Software for Combination Tubes of Pressure Pipes;
压力管道组合管件模块化设计软件开发
2.
Vibration characteristic analysis of pressure pipes with fluid-structure interaction;
压力管道流固耦合振动特性分析
3.
Experimental study on spectral characteristics of acoustic emission from pressure pipe leakage;
压力管道泄漏声发射信号频谱特性实验研究
4) pressure piping
压力管道
1.
Welding Technique and Quality Control in Pressure Piping Engineering;
压力管道工程焊接技术与质量控制
2.
The Study of Safety Assessment Engineering Method of the Pressure Piping Containing LOP Defect;
未焊透缺陷压力管道安全评定工程方法研究
3.
Through investigating the safety administration of pressure piping application units in one town,the situation of pressure piping application safety in the enterprises in rural area was analyzed,and the measure and proposal for improvement were presented.
通过对某乡镇压力管道使用单位安全管理的实地调查,来分析乡镇企业压力管道的安全状况,提出措施及建议。
5) penstock
[英]['penstɔk] [美]['pɛn,stɑk]
压力管道
1.
The technique of single face welding with double face forming of penstock;
压力管道单面焊双面成形技术
2.
Study on formulas for calculating crack width of penstocks with inner steel liner and outer reinforced concrete;
钢衬钢筋混凝土压力管道裂缝宽度公式的探讨
3.
Construction of inclined shaft for the penstock of the Yele Hydropower Station;
冶勒水电站压力管道斜井施工
6) penstocks
压力管道
1.
Application of ANSYS to analying steel-reinforced concrete penstocks;
ANSYS在钢衬钢筋混凝土压力管道分析中的应用
2.
Analysis of cracks causation of reinforced concrete penstocks of Yangling Hydropower station;
杨凌水电站钢筋混凝土压力管道裂缝成因分析
3.
Analysis on Steel Stress of the Penstocks of Three Gorges Hydroelectric Station
三峡电站压力管道钢材受力分析
补充资料：锅炉、压力容器、压力管道及特种设备定期检验
锅炉、压力容器、压力管道及特种设备定期检验
periodic inspection of boilers, pressure vessels, pressure piping and special equipment
guolu YOli侧飞扣1 YOli gLJal对印ji tez陌叩劝以拍1 dingqi】，on四n锅炉、压力容器、压力管道及特种设备定期检验(peri诫c inspectionof城le。，p~切reves-Sels，p~二piPing ands衅过闪uiplr屺nt)为保证设备的安全使用，规定设备必须按一定周期进行法定的、强制性的检验。定期检验由政府设立的检验所、使用单位或行业检验站进行。检验单位及检验人员必须具有与所检设备相适应的资格。设备使用单位应该建立定期检验制度，做好检验计划，按时向检验单位提出申请。检验单位应该保证及时进行检验，检验按有关检验规则进行。检验时，设备使用单位应做好配合工作，提供必要的运行资料。检验完毕，检验单位要出具检验报告，对设备能否使用，要作出明确结论。如设备有缺陷，要提出是否修理、监护使用和报废的处理意见。锅炉压力容器安全监察机构根据检验机构的报告，发使用许可证书。有缺陷的，责令使用单位修理，修理后检验仍不符合安全要求的，则通知报废。使用单位逾期不进行定期检验，锅炉压力容器安全监察机构有权停止其设备运行。(陈亦惠)
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条