1) ultra height
超高度
1.
The intention of writing this article is to explore the quality control method of similar construction through the successful construction quality control experiences ofa certain cast- in- situ concrete construction with ultra height, large span, large section, large volume and a special requirement for style.
文章意在通过某超高度、大跨度、大截面、大体积具有特殊造型要求的现浇混凝土施工质量控制的成功经验,探索类似工程施工质量控制的方法。
2) super high density
超高密度
1.
Considering the complicated situations such as uncertainly in strata pressure, high abnormal pressure coefficient, strata being easy to collapse, co-existence of well blowout and lost circulation etc, the article analyzes technical difficulties of drilling fluid with super high density, decides prescription of drilling fluid with density of over 2.
针对赤水官渡地区的地层压力规律性差,异常压力系数高,地层易垮塌、喷漏并存等复杂情况,分析了超高密度钻井液技术难点,在优选处理剂和控制合适的膨润土用量的基础上,确定了密度为2。
3) super strength
超高强度
1.
This paper analyzes the material mechanical properties of domestic new alloy steel 38SiMnVBE with high cost performance and super strength,and the material mechanical properties of foreign typical high performance alloy structure steels,as well as their applications in automotive components and parts.
分析了高性价比、超高强度38SiM nVBE合金结构钢和国外典型高性能合金结构钢的材料力学性能,以及在汽车零部件上的应用现状,探讨了其今后在汽车传动零件上应用的可能性。
4) Ultra High Strength
超高强度
1.
Effect of Cu Content on Mechanical Properties of Ultra High Strength Low Carbon Bainitic Steel;
铜含量对超高强度低碳贝氏体钢力学性能的影响
2.
Using rapid solidification (RS) and powder metallurgy (PM) technique, Al90Mn8Ce2 bulk alloy with ultra high strength and 20 mm in diameter and 10 mm in length has been prepared.
用快速凝固/粉末冶金法,制备了致密超高强度块体Al90Mn8Ce2合金,其尺寸为直径20 mm、长10 mm。
5) super-high strength
超高强度
1.
In this paper,the development and application of super-high strength aluminum alloys abroard,suchas BR96,7090,CW67 and 7055 were reviewed.
本文以Ｂ９６、７０９０、ＣＷ６７及７０５５等合金为典型，对国外超高强度铝合金的发展与应用进行了评述，初步介绍了国内７Ａ５５合金的发展现状，并与国外同类材料进行了对比。
6) super-high thickness cutting
超高厚度
1.
Based on these opinions elemental requirements were give and the cooling liquid used in super-high thickness cutting was presented.
阐述了高速走丝电火花线切割超高厚度切割的基本条件,分析了目前市场上通用的工作液在超高厚度切割方面存在的问题,由此提出可进行超高厚度切割工作液的基本要求,并成功研制出超高厚度切割工作液,加工中表明其体现出与现有工作液不同的加工工艺特性。
补充资料：超超
1.谓超然出尘。 2.高高在上貌。 3.犹绰绰。 4.见"超超玄箸"。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条