1) the wash and abrasion type
冲蚀磨蚀型
1.
The investigation shows that the length of the wash and abrasion type and collapse type of the bank failure is above one half of the investigated sections in the Yangtze Three Gorges Project Region.
三峡库区重点库岸段塌岸调查结果显示,土质冲蚀磨蚀型和坍塌型塌岸占其长度的50%以上。
2) model for erosion
冲蚀磨损模型
3) erosion wear
冲蚀磨损
1.
Effect of erosion wear on epoxy bond coating with nanometer fillers;
纳米填料对环氧胶粘涂层冲蚀磨损性能的影响
2.
Study on erosion wear properties of epoxy adhesive coating;
环氧胶粘涂层冲蚀磨损特性研究
3.
Analyses of erosion wear characteristic and structure research on hydraulic valve;
液压阀冲蚀磨损特性分析与结构探讨
4) erosion
[英][i'rəuʒən] [美][ɪ'roʒən]
冲蚀磨损
1.
Study on Erosion Wear Mechanisms of WC-Co Coatings Prepared by Supersonic Plasma Spraying;
超音速等离子喷涂WC-Co涂层的冲蚀磨损机理研究
2.
The study of erosion resistance of sprayed nickel based alloy coating under the impacting of coke partcles;
镍基喷涂层抗焦粒冲蚀磨损性能的研究
5) erosive wear
冲蚀磨损
1.
The results show that the erosive wear resistances of the two heat treated Cr-Mn-Cu alloy white cast iron materials are 1.
以铸态铬锰铜合金白口铸铁为对比材料,考察了热处理后的铬锰铜合金白口铸铁的抗冲蚀磨损性能,并对试验材料的冲击断口形貌、抗冲蚀磨损失效机理和冲蚀磨损横切面的金相组织进行了分析。
2.
The goal of this research was to identify the relationship between composition and mechanical properties of clay toughened epoxy resins and their erosive wear resistance.
研究了粘土改性环氧树脂的浆液体冲蚀磨损性能。
3.
The goal of this research is to identify the relationship between composition and mechanical properties of polyurethane (PU) toughened epoxy resins and their erosive wear resistance.
研究了聚氨酯(PU)增韧环氧树脂(EP)的浆液体冲蚀磨损性能。
6) erosion resistance
冲蚀磨损
1.
Study on microstructure and erosion resistance of Al_2O_3 reinforced Ni-base alloy coating;
氧化铝增强镍基合金涂层的组织与耐冲蚀磨损性能研究
2.
Metallographic examination, hardness and erosion resistance tests showed that the softer the austenite or austenite + martensite surfacing layers, the better erosion resistance at large angle erosion; while surfacing layers with small amounts of precipitat.
通过金相分析、硬度测定和冲蚀磨损试验,表明堆焊层主要为奥氏体或奥氏体+马氏体组织,堆焊层硬度较低,具有良好的抗大角度冲蚀磨损性能。
3.
Mechanisms and erosion resistance of pressless (PL) sintered SiC, hot-pressed (HP)SiC, hot-isostatic-pressed (HIP) SiC ceramics are discussed in this paper.
研究了无压（PL）；热压（HP），热等静压（HIP）同烧结SiC陶瓷的室温冲蚀磨损行为热等静压SiC陶瓷具有良好的综合力学性能和细致的组织结构，其冲蚀磨损耐磨性比无压和热压烧结SiC陶瓷要
补充资料：磨蚀硬度
分子式：
CAS号：
性质：也称磨耗硬度。是在规定条件下测得的材料抗磨能力的是量度。方法要点是对着试片45°方向使金刚砂粒子自由下落其上，测量它表面光泽的变化。本方法属冲击磨耗的范畴，特别对于光滑表面的耐磨性有重要意义，例如测定油漆、涂料的耐磨性就经常使用该方法，具体测定条件有标准试验方法。
CAS号：
性质：也称磨耗硬度。是在规定条件下测得的材料抗磨能力的是量度。方法要点是对着试片45°方向使金刚砂粒子自由下落其上，测量它表面光泽的变化。本方法属冲击磨耗的范畴，特别对于光滑表面的耐磨性有重要意义，例如测定油漆、涂料的耐磨性就经常使用该方法，具体测定条件有标准试验方法。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条