1)  nominal rigidity
名义刚度
1.
Three concepts,such as the dead,live load ratio between cable and girder,and the nominal rigidity of the bridge,are provided,and the bridge is defined according to its structural type in order to reveal its mechanical essence.
简要叙述矮塔斜拉桥在国内外的应用及研究状况,讨论该种桥型的中文和英文关键词,提出索梁恒载比、索梁活载比和名义刚度的概念,并对这种桥型进行界定,试图揭示这类桥梁的力学本质,最后对该种桥型的发展作了展望。
2)  Nominal rigidity ratio
名义刚度比
3)  name
名义
1.
In order to clarify the relations between New Yuefu and Yue Baishi , it is necessary to define its name first.
为厘清新乐府与元白诗派的成立之间的关系,有必要先对其名义作一界定。
4)  nominal strength
名义强度
1.
The research progeny about corrosion character and deterioration mechanism of mechanical property of the corroded steel bars in concrete are mainly summarized and discussed in this article,which also expounds the deteriorating regularity of nominal strength and ductility of the corroded steel bars .
本文主要总结与讨论了混凝土内锈蚀钢筋的锈蚀特征、力学性能退化机理等方面的研究成果,阐述了钢筋锈蚀后其名义强度与延性的退化规律,为研究和评估锈蚀钢筋的力学性能提供了依据。
5)  nominal common difference
名义公差
1.
Through the dynamics analysis on the relationship between wheel and rail surface,based on the experimental data from scientific research institutes,we find the effective measure to avoid suspension derailment of empty trains that is to reduce the gap between rail and wheel in straight section(nominal common difference).
通过对车辆车轮与轨面间的动力学原理分析,结合科研部门的大量试验数据,提出减小直线段轮轨间隙(名义公差)是防止空车悬浮脱轨的有效方法。
6)  nominal stress
名义应力
1.
Study of fatigue strength assessment methods of welded structures based on nominal stress;
基于名义应力的焊接结构疲劳强度评定方法研究
2.
The fatigue strength of duplex stainless steel welded jointing with longitudinal fillet welded gusset and with longitudinal flat side gusset welded on plate were evaluated by hot spot stress,and the hot spot stress S-N curves were obtained and compared with the nominal stress S-N curves.
针对双相不锈钢焊接结构的疲劳性能问题,通过试验对双相不锈钢纵向角接板焊接接头和侧面角接板焊接接头疲劳强度用热点应力进行了评定,做出了热点应力S N曲线并与名义应力疲劳评定进行了比较。
参考词条
补充资料:JPZ型三向等刚度橡胶减震器
分子式:
CAS号:

性质:JPZ-type tridirective equal rigid rubber mounting  橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成,模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。

说明:补充资料仅用于学习参考,请勿用于其它任何用途。