1) forced steering mechanism
迫导向机构
1.
Study of forced steering mechanism of low-speed maglev train;
低速磁浮列车迫导向机构的研究
2.
The effect of the levitation module and the forced steering mechanism of the running gears on the curve negotiation performance is given.
分析了磁浮列车走行机构通过曲线时的运动关系,给出了走行机构悬浮模块及迫导向机构对曲线通过性能的影响,并以五单元走行机构为例说明了曲线通过原理。
2) guiding mechanism
导向机构
1.
The inherent frequency of key parts-guiding mechanism is measured out as well.
并测出超临速自磨机的关键部件—导向机构的固有频率。
2.
This kind of torch is designed with straight handle,using special electromagnet starting and lifting mechanism,and guiding mechanism.
复合热源螺柱焊接工艺是一种新型螺柱焊接技术,在深入试验研究传统电弧螺柱焊枪的基础上,根据复合热源螺柱焊接和空心螺柱旋弧焊接的工艺需求,设计研制了一种适用于中厚板大直径复合热源螺柱自动焊接的大功率焊枪,该焊枪采用直柄式设计,使用了独具特色的专用电磁铁、引弧提升机构和导向机构,采用所设计的大功率自动螺柱焊枪,进行了8~30 mm板厚12~21 mm直径的自动螺柱焊接工艺试验,焊接过程稳定、接头饱满,接头强度与螺柱强度之比达到1。
3) Control bars
导向机构
1.
By analyzing the diagram of control bars of double wishbone suspension with twin torsion bar, the geometry characteristic of control bars and calculating method of the suspension s rigidity are gotten.
分析了双横臂双扭杆悬架的导向机构模型简图 ,得到了导向机构的运动关系和进行悬架刚度计算的方程 ;以满足悬架载荷要求和悬架刚度要求为前提 ,分析了上下扭杆的刚度匹配条件 ;在上下扭杆在悬架运动时的强度始终相等的前提下 ,分析了上下扭杆的等强度条件 。
4) steering mechanism
导向机构
1.
Optimization precision of steering mechanism for HTCR radial bogie;
HTCR 径向转向架导向机构最优化精度综合的研究
2.
This paper describes the main mechanical structure design of a power self-support in-pipe robot,including the designs of power self-support part,supporting wheel part and steering mechanism,which provides a very important base for studying new power self-support in-pipe robots.
详细论述了能源自给式管道机器人总体机械结构设计,包括发电蓄能部分结构设计、支撑轮组件的设计和导向机构设计,为新型能源自给式管道机器人的研究奠定了基础。
5) guide mechanism
导向机构
1.
Design of Guide Mechanism for Air Spring Suspension System Based on Virtual Prototype Technology;
基于虚拟样机技术的汽车空气悬架系统导向机构设计
2.
In order to testify the varifocusing performance and image quality of one novel continuous in- frared zoom lens, two kinds of cam mechanism were described according to the optic design of the infrared zoom lens, cam mechanism, guide mechanism and focusing mechanism was discussed in detail, and suppression methods on the stray radi- ation of the system were introduced.
为了验证红外连续变焦镜头的变倍性能及其成像质量,根据某红外连续变焦镜头的光学设计特点,通过对其机械结构进行选型,最终采用不同形式的凸轮机构来实现红外变焦距镜头变倍、调焦过程,对凸轮机构、变倍导向机构、调焦机构等作了较详细的说明,并从机械设计的角度出发,对系统的杂散辐射提出了抑制措施。
6) forced steering
迫导向
1.
A dynamic model for the meter gauge passenger car with forced steering bogies is built, in which some effective treatment methods of the forced steering mechanism are presented, and the effect of the mechanism parameters of the forced steering bogies on the dynamic performances of the passenger car is investigated.
建立了米轨迫导向转向架客车的动力学模型 ,提出了迫导向机构的等效处理方法 ,以研究迫导向转向架导向机构参数对客车动力学性能的影响。
2.
The fundamental principles of the forced steering bogies are expounded.
阐述了迫导向转向架基本原理 ,提出一种简单易行的米轨客车迫导向转向架方案 ,并通过建立该转向架的非线性动力学模型 ,分析了导向机构设计对运动稳定性和曲线通过性能的影
补充资料:蹙迫
1.亦作"?迫"。 2.逼迫。 3.逼近。 4.损伤。 5.困窘,窘迫。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条