1) calibration-curve method
标定曲线方法
1.
A set of integrated treatment methods to ensure high accuracy to the intelligent radiation thickness gauge is presented,such as choosing a suitable radiation source according to different object and measurement range,calibration-curve method,automatic dynamic adjustment,dynamic temperature compensati.
介绍了薄带材智能辐射测厚仪的测量原理、结构组成;研究与分析了影响辐射测厚仪测量精度的各种因素;给出了一整套相应的保证和提高辐射测厚仪的测量精度的集成处理方法,如根据不同被测对象和测量范围选择不同放射源、标定曲线方法、动态自动校正、动态温度补偿等。
2) Standard Curve Quantitation Method (SCQM)
标准曲线定量法
3) calibration curve
定标曲线
1.
The laser_induced breakdown spectroscopy(LIBS) calibration curves of the Fe and Ni trace elements are also determined in buffer gases He,Ar,Air and in vacuum.
实验上研究了最佳实验条件下铅黄铜合金中Ni,Fe两种杂质元素的LIBS分析谱线,在氦气、氩气、空气和真空等4种环境中,测定了Ni,Fe两种杂质元素分析中的LIBS定标曲线,定标曲线的拟合标准偏差在0。
2.
The calibration curves of Pb content were constructed with the spectrogram acquired in experiments.
利用实验光谱图建立了Pb含量的定标曲线。
3.
The calibration curve method for LIBS quantitative analysis is introduced.
介绍了用于激光感生击穿光谱技术定量分析的定标曲线方法,并以5种煤样作为实验对象,选取激光击穿煤粉时碳元素505。
4) calibration curve
标定曲线
1.
The paper explains the measuring principle and calculation procedure of already calibrated flow measuring devices, presents a new technique for extrapolating the calibration curve, derives the functional relationship between practically used discharge coefficients and Renold s number of generally used flow measuring devices liable for calibration.
介绍了已标定流量测量装置的流置测量计算方法和标定曲线外推新技术,推导出常用标定流量测量装置实际应用的流出系数和雷诺数的关系式,开发了专用流量测量计算软件,并给出了应用实例。
2.
In this study, the freezing and thawing characteristic curves of umber soil with different initial water content were measured by TDR and NMR methods, and the reliability of the calibration curves of TDR method was verifi.
通过应用NMR和TDR两种方法对不同初始含水率下的棕壤土冻融特征曲线的测定,对TDR法的标定曲线的可靠性进行了验证。
3.
According to the overall dynamic compliance C of curve of average load-relative displacement and the crack growth length, the path and velocity of crack growth is obtained by the calibration curve method.
利用一维试验原理 ,在冲击拉伸试验装置上实现了周边切口短圆柱试件的动态起裂和动态止裂试验 ,利用止裂试验中不同的裂纹止裂长度Δa和止裂点处的总体柔度 ,拟合一标定曲线 ,根据 P δ曲线上每一点的总体柔度由标定曲线来确定裂纹的稳态扩展轨迹 ,从而得到裂纹的扩展速度 。
5) calibration curves
标定曲线
1.
Mathematical expression of calibration curves for measuring friction factor by ring upsetting;
圆环镦粗法测摩擦因子用标定曲线的公式表达
6) calibration methods
标定方法
1.
The separate mechanism and the calibration methods used by gel permeation chromatography were presented.
阐述了凝胶色谱法的分离机理,详细地介绍了凝胶色谱法中应用的不同标定方法。
补充资料：Solidwors2001中绘制和控制样条曲线的方法
SolidWorks2001中绘制和控制样条曲线的方法<在工业产品的造型设计中，为了做到产品良好的视觉效果，经常会使用样条曲线作为草图建立特征。本文将初步介绍一下在SolidWorks2001 中绘制和控制样条曲线的方法。
1． 样条曲线的绘制
样条曲线是通过一系列的点进行平滑过渡形成的，这些点称为样条曲线型值点。SolidWorks2001 提供了两种绘制样条曲线的方法，即交替样条曲线绘制方式和拖动式。
n 交替样条曲线绘制方式
交替样条曲线绘制是分别在通过样条曲线型值点的地方单击生成样条曲线的方法。
1) 新建一幅草图，单击“样条曲线”按钮 
。
2) 依次单击图1（a）所示的“点1 ”~“点4，并在“点5 ”位置双击，形成图1（b）所式的样条曲线。
3) 再次单击“样条曲线”按钮 ，结束样条曲线绘制。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条