1) section stiffness
截面刚度
1.
In order to analyze the section stiffness of the double steel-concrete composite beams at the serviceability limit stage, section stiffness is calculated according to the position where the neutral axis is.
对钢—混凝土双面结合梁在支座和跨中的截面刚度进行了分析研究,按照中和轴在钢梁内、下翼缘混凝土板内两种情况分别对钢-混凝土双面结合梁截面刚度进行了计算。
2.
Aimed at the mechanical characteristics of type of LGJQT-1400 wire,the section stiffness of special light steel cored aluminum strand wire is analyzed according to its geometrical makeup.
针对 L GJQT- 140 0导线的力学性能 ,从其组成的几何规律出发 ,分析了特种轻型钢铝绞制粗导线的截面刚度。
3.
On the basis of the short-term stiffness formulas provided by the current concrete codes for prestressed flexural member and normal flexural member,the formulas of cracking moment,pre-cracking section stiffness and post-cracking section stiffness for the horizontal displacement calculation of cantilever column which under axial force action and without axial force action are deduced.
根据现行规范给出的预应力混凝土受弯构件短期刚度公式和普通受弯构件短期刚度公式,推导出了有轴力作用下和无轴力作用下的悬臂柱开裂弯矩、开裂前截面刚度和开裂后截面刚度的计算公式;在对钢筋弹性模量与混凝土弹性模量比、截面配筋率、截面有效高度和整截面高度比以及轴力大小等可影响轴力作用的一些参数因素进行分析的同时,得到这些因素对轴力作用的影响程度以及各因素间互相作用或制约的影响关系等定性规律。
2) elastic-plastic section stiffness
弹塑性截面刚度
3) section elastic stiffness
截面弹性刚度
1.
Now values for section elastic stiffness of reinforced concrete bridge piers are not uniformly prescribed in Chinese codes for bridge seismic design, and generally the gross section stiffness is adoped as the section elastic stiffness, which is quite different from the proper section elastic stiffness.
目前我国桥梁抗震设计规范对钢筋混凝土桥墩的截面弹性刚度取值没有统一的规定 ,一般取毛截面刚度来作为截面的弹性刚度 ,这与合理的取值之间有较大的差异 。
4) section stiffness matrix
截面刚度矩阵
1.
According to section stiffness matrix and available displacement mode,element stiffness matrix of elastoplastic stage was derived in this paper.
可基于截面刚度矩阵以及现有的位移模式推导出弹塑性阶段的单元刚度矩阵。
5) torsional stiffness of cross section
截面抗扭刚度
补充资料：JPZ型三向等刚度橡胶减震器
分子式：
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条