1) non-metallic micro-inclusions
非金属显微夹杂物
1.
The distributions and characteristics of non-metallic micro-inclusions of GCr15 and SS400 casting slabs in process of BOF-LF-VD-CC were analyzed by metallographic volume ratio method,in virtue of tracer method and electronic microscope.
借助扫描电镜和示踪法,利用金相学体积率法对BOF-LF-VD-CC流程生产的GCr15方坯连铸轴承钢和SS400板坯连铸中碳钢中非金属显微夹杂物的类型、特点、数量和分布进行了分析。
2) non-metallic inclusions
非金属夹杂物
1.
Research on cleanness and non-metallic inclusions of low carbon aluminum killed steel produced by BOF-LF-FTSC at Tang Steel;
低碳铝镇静钢洁净度及非金属夹杂物的研究
2.
Origin of non-metallic inclusions in 0Cr18Ni9 stainless steel;
0Cr18Ni9不锈钢中非金属夹杂物来源
3.
Analysis and control of non-metallic inclusions in steel on "6σ" principle;
采用“6σ方法”分析和控制钢中非金属夹杂物
3) non-metallic inclusion
非金属夹杂物
1.
Icfluence of Non-Metallic Inclusion and Surface Condition on Fatigue Property of High Strength Spring Steel;
非金属夹杂物和表面状态对高强度弹簧钢疲劳性能的影响
2.
Uncertainty and detection of the non-metallic inclusion s status in steel;
钢中非金属夹杂物存在状态的不确定性与检测
3.
Study on Non-Metallic Inclusions in Maraging Steel Produced by Electroslag Remelting Process
电渣重熔马氏体时效钢中的非金属夹杂物研究
4) nonmetallic inclusion
非金属夹杂物
1.
Study on the mechanism of exceptional spectrum signal produced by nonmetallic inclusions in steel;
钢中非金属夹杂物异常光谱信号产生机理的研究
2.
Hard Spots and Nonmetallic Inclusion in Aluminum Die Casting;
铝压铸件中的硬质点及非金属夹杂物
3.
We checked gas amount and hot acid etched test for the tube,made the microcosmic analysis by metallurgical microscope and electric scanning microscope,then concluded that nonmetallic inclusion was the main reason to result in flaw of thread.
我们在对管体进行了气体含量及热酸低倍检验的同时,利用金相显微镜和扫描电镜对其进行微观分析,得出非金属夹杂物是引起断扣问题的主要原因,并对夹杂物做定性分析,以便找出其来源,同时也提出相应的改进措施。
5) nonmetallic inclusions
非金属夹杂物
1.
The study of nonmetallic inclusions in continuous casting big blooms;
连铸大方坯非金属夹杂物研究
2.
Using systematic sampling and comprehensive analysis, the variation of total oxygen content and amount, dimension and distribution of nonmetallic inclusions were studied systematically during the production process of hot metal pretreatment-LD-LF-VD-slab CC in Angang.
针对鞍钢炼钢厂"铁水预处理→LD→LF→VD→CC"X70生产流程,采用系统取样,综合分析的方法,对LF处理前后、VD处理前后、中间包、结晶器和铸坯中的T[O]、显微非金属夹杂物的类型、数量及尺寸分布进行了系统研究。
3.
In order to improve the quality of the products and the pure degree of the steel;the type,quantity,size,composition and distribution of the nonmetallic inclusions present in continuous cast slabs made by Weiyuan Iron and Steel Co.
为了进一步提高产品质量,提高钢材的纯净度,采用了光学显微镜、扫描电镜、X射线能谱仪以及电解称重法对威钢板坯连铸生产过程中非金属夹杂物的类型、数量、大小、组成及分布等进行了研究,并且讨论了目前生产工艺中非金属夹杂物的来源。
6) non metallic inclusions
非金属夹杂物
1.
A software package called Thermo Calc was used for analyzing the non metallic inclusions in the steels.
对预硬型塑料模具钢ASSAB718和国产的GC718的切削加工性能进行了对比性研究 ,并结合Thermo Calc软件对钢中非金属夹杂物进行了分析。
2.
Investigation has been made on variation of T[O] and non metallic inclusions in high pressure gas cylinder steel during production with BOF RH CC route.
对转炉— RH精炼—连铸工艺生产高压气瓶用钢 T[O]变化及非金属夹杂物进行研究的结果表明 ,在转炉出钢过程由于炉渣与脱氧产物作用生成的粗大球状夹杂物及铝脱氧生成的大尺寸 Al2 O3簇群状夹杂物绝大多数可由钢液排除 ,铸坯中存在的夹杂物主要是较小的块状和簇群状 Al2 O3及少量由于结晶器保护渣卷入造成的球状夹杂物。
3.
The coagulation behavior of micro sized non metallic inclusions in molten metal processed by ultrasound was analyzed and discussed.
针对超声波作用下金属液中微小非金属夹杂物的凝聚过程进行了分析研究。
补充资料：夹杂
分子式：
CAS号：
性质：指复合材料在生产过程中，无意之中夹带的形状大小不等的外来物，如颗粒、碎片、薄膜等。为保证复合材料的质量，必须严格避免夹杂现象的发生。夹杂物会引起复合材料内部的应力集中以及力的传递受到阻碍，但一般认为，当夹杂物含量不超过0.5％，对复合材料性能影响不大。检测夹杂的有效手段是x射线法。
CAS号：
性质：指复合材料在生产过程中，无意之中夹带的形状大小不等的外来物，如颗粒、碎片、薄膜等。为保证复合材料的质量，必须严格避免夹杂现象的发生。夹杂物会引起复合材料内部的应力集中以及力的传递受到阻碍，但一般认为，当夹杂物含量不超过0.5％，对复合材料性能影响不大。检测夹杂的有效手段是x射线法。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条