1) cooling rate
冷却率
1.
In this paper the effects of stratospheric volcanic aerosols on longwave radiation budgets at the top of the atmosphere and on the surface and the infrared cooling rates in the atmosphere were investigated through radiative transfer calculations for different atmospheres under clear and cloudy conditions.
通过辐射传输计算，对不同大气状况下平流层火山气溶胶对地面和大气顶长波辐射收支及大气中长波辐射冷却率的影响进行了分析。
2) cooling rate
冷却速率
1.
Quantitative relationship between secondary dendrite arm spacing and solidification cooling rate of AZ31 magnesium alloy;
AZ31镁合金的凝固冷却速率与二次枝晶间距的定量关系
2.
A simple model for calculation of thermal sprayed splat cooling rate;
一种计算热喷涂层片冷却速率的简单模型
3.
A new approach to evaluate cooling rates of melt droplets in close-coupled gas atomization;
一种表征紧耦合气雾化中熔滴冷却速率的新方法
3) cooling efficiency
冷却效率
1.
Influence of aerodynamic parameter on the temperature gradient and cooling efficiency for effusion wall cooling method;
多斜孔冷却方式气动参数对壁温梯度和冷却效率的影响
2.
Experimental study of cooling efficiency of film cooling with tab;
突片作用下气膜冷却效率的试验研究
3.
Investigation of the wall temperature distribution and cooling efficiency for impingement/effusion cooling scheme;
冲击/发散冷却壁温分布和冷却效率研究
4) cooling rates
冷却速率
1.
Effect of cooling rates on the microstructure of proeutectoid ferrite in Fe-0.76%C steel in high magnetic field;
强磁场下冷却速率对Fe-0.76%C钢先共析铁素体组织的影响
2.
The effect of cooling rates on the solidification process of Al-2.
试验研究了冷却速率对Al 2 06%Si 1 58%Mg三元合金凝固过程的影响。
3.
The influence of cooling rates on mechanical property of PE100 pipe material prepared by different cooling ways was studied.
采用不同的冷却方式研究冷却速率对聚乙烯管材专用料力学性能的影响,发现随冷却速率减小,其屈服强度增大,冲击强度先升高后降低,空气冷却时最高,最大差值达12 kJ/m2。
5) Cooling effectiveness
冷却效率
1.
Study of overall cooling effectiveness of discrete holes with different angles to concave wall;
弯曲多孔壁不同倾斜角气膜孔整体气膜冷却效率研究
2.
Detailed heat transfer and full coverage film cooling measurements were conducted on the turbine blade surface,primarily research the effect of different reynolds number and mass flow ratio on local heat transfer and film cooling effectiveness.
对全气膜覆盖的涡轮导向叶片的表面进行了详细的传热实验研究,重点研究了不同质流比和不同雷诺数对当地气膜冷却效率和换热系数的影响。
3.
To investigate the influence of the hole shape on the film cooling effectiveness of the maze composition structure of a combustor,a numerical study on the distribution of its wall temperature and cooling effectiveness was performed when the outside wall holes were dust-pan shaped holes,cone shaped holes and round holes.
为了获得开孔形状对燃烧室新型迷宫复合冷却结构冷却效率的影响规律,采用数值模拟方法研究迷宫冷却结构的外侧壁冷却孔分别为簸箕形孔、圆锥形孔和圆柱形孔时内外壁温的分布情况,获得其壁温及冷却效率的分布规律,并在迷宫冷却结构三层壁的热侧面对它们的冷却效率进行对比。
6) cooling times rate
冷却倍率
1.
The paper analyzed the relation between cooling volume of circulating water and entry temperature of circulating water in view of cooling times rate and enthalpy drop,and proved theoretically feasibility of the conception——that inner circulating water cooling system is stopped and only riverside circulating water cooling system is used in winter and spring,then put the conception to practice.
从冷却倍率、焓降两个方面对循环水冷却水量与循环水进口温度之间的变化关系进行分析， 从理论上证明了在冬、春两季将内循环水冷却系统退出停运而只投入江边循环水冷却系统这一设想的可行性， 并将此设想付诸实践。
补充资料：电导率(见电阻率)
电导率(见电阻率)
conductivity
d!日nd日O}已电导率(eonduetivity)见电阻率。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条