1) suspension stiffness
悬浮刚度
1.
The analytical results show that the suspension stiffness of the controlled-PM maglev systems is positively proportional to the feedback coefficient of air gap, and the suspension damping is not only positively proportional to the feedback coefficient of air gap.
分析结果表明:电磁永磁混合悬浮系统的悬浮刚度与间隙反馈系数成正比,悬浮阻尼不仅与间隙反馈系数成正比,而且也与间隙变化速率反馈控制系数成正比。
2.
The suspension stiffness and damping of an actively controlled electromagnetic suspension system were analyzed theoretically and numerically.
以常导磁浮车辆的悬浮导向基本单元为对象,对采用两级串联悬浮控制的单磁铁悬浮系统进行悬浮刚度和阻尼特性的理论与数值分析。
3) magnetic levitation stiffness
磁悬浮支承刚度
5) mounting stiffness
悬置刚度
1.
By comparing the simulation results under different main bearing load,the effect of the coupling flange,the mounting stiffness and the elasticity of shaft coupling on main bearing load were discussed.
通过比较不同模型主轴承载荷差异,探讨了连接法兰、悬置刚度和联轴节等安装条件对主轴承载荷计算的影响。
6) suspension velocity
悬浮速度
1.
Experimental determination of the test weight and suspension velocity of the rapeseed kernel and husk and research on the rapeseed hull-kernel vibration hierarchical classification were presented for structure design and the choice of operating parameters of the kernel husk separator of rapeseed.
为给油菜籽仁皮分离机的结构设计和操作参数选用提供可靠依据,试验测定了油菜籽仁、皮的容重和悬浮速度,并对油菜籽仁皮混合物的振动分层进行了试验研究,采用数理统计方法建立数学模型,探讨了振动强度对油菜籽仁皮振动分层效果的影响。
2.
Using particle size region(PSR)criterion makes the study of suspension velocity in the slurry more simplified and reliable.
实验采用粒粒范围判据判定颗粒周围的流态，使料浆中颗粒悬浮速度的测量计算变得更简单、准确，由串联釜模型参数与物料在反应器中的返混建立的对应关系，对铝土矿悬浮溶出器设计参数进行了预测。
3.
Based on the analysis of current pneumatic conveyance mode and the influence of pipe length, velocity and ash-air quality ratio on pipe pressure, the conveyance characteristics of pipes were discussed, the cause of pipeline blocking was found out and the selection method for suspension velocity was given, providing guidance for energy-saving and consumption reduction in the design.
通过分析目前气力输送方式及管道长度、流速、灰气质量比对管道压力的影响,阐述管道输送特性,找出堵管原因,并给出悬浮速度的选择方法,为浓相正压气力输送设计中的节能降耗提供指导性结论。
补充资料：JPZ型三向等刚度橡胶减震器
分子式：
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
CAS号：
性质：JPZ-type tridirective equal rigid rubber mounting 橡胶减震器的一种。具有x、y、z三个方向等刚度、等自震频率。按负荷大小可分为JPZ-1、JPZ-2两种型号。由中央金属芯柱、伞形金属罩及橡胶连接而成，模压法生产。可满足导弹控制仪等设备的隔震和抗冲击要求。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条