1) rubber asphalt sand gel
橡胶沥青砂胶
1.
Through anti shearing strength test and comparison among different binding material and anti-shearing strength test of rubber asphalt sand gel on surface of concrete,it is proven that it has high anti-shearing strength on concrete surface,and because of strong accommodation of its process to bridge deck leveln.
橡胶沥青砂胶是西部交通科技项目“桥面铺装材料与技术研究”在混凝土桥面铺装方面的一项研究成果。
2) Asphalt rubber
橡胶沥青
1.
Laboratory study on process parameters of asphalt rubber and their effects on performance;
橡胶沥青工艺参数对其性能影响的试验研究
2.
Key technical parameters analysis for production technology of asphalt rubber;
橡胶沥青生产工艺关键技术参数的研究
3.
Mix design method of asphalt rubber open-graded friction course and its application in overlay
橡胶沥青开级配混合料设计方法及其在罩面工程中的应用(英文)
3) Rubber asphalt
橡胶沥青
1.
The rubber asphalt detritus under-sealed layer technique of semi-rigid basis asphalt pavement;
半刚性基层沥青路面橡胶沥青碎石下封层技术
2.
Research of the property of rubber asphalt SAMI covered by anti-cracking layer;
橡胶沥青SAMI加铺阻裂层的性能研究
3.
The rubber asphalt product is one kind of new highly effective and environment-protective road material.
橡胶沥青产品是一种新型高效、环保的筑路材料,其在欧美发达国家已经得到了较大规模的推广,但在我国的应用尚处于起步阶段,本文着重介绍了美国加州橡胶沥青产品的设计、生产、施工原理,为今后我国橡胶沥青的科学研究及大规模应用提供了借鉴。
5) asphalt-rubber
橡胶沥青
1.
Preparation process and performance of asphalt-rubber;
橡胶沥青制备工艺及其性能的研究
2.
Application of asphalt-rubber to pouring semi-flexible pavement
橡胶沥青在灌入式半柔性路面中的应用
3.
In this paper,the pavement design,high temperature stability,low-temperature cracking and water stability of asphalt-rubber semi-flexible pavement are experimented and the experiment road is paved,which show that semi-flexible pavement with asphalt-rubber has good road performance.
针对橡胶粉改性沥青半柔性路面的设计方法、高温稳定性、低温抗裂性和水稳定性等性能进行室内试验研究,表明橡胶沥青半柔性路面具有良好的路用性能。
6) asphalt and rubber
沥青-橡胶
1.
Performance research of SMA mixture using asphalt and rubber;
沥青-橡胶拌制SMA混合料的性能研究
补充资料:橡胶模具、橡胶压模、橡胶硫化模
分子式:
CAS号:
性质:又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得,并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同,型腔尺寸必须考虑不同橡胶的收缩率,在产品尺寸基础上进行放大或缩小,方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
CAS号:
性质:又称橡胶模具、橡胶压模、橡胶硫化模。用于压制橡胶产品的金属模型。一般用钢材(如45号钢)按图纸要求经机械加工而制得,并经热处理以提高其硬度及耐磨性。模具型腔与产品结构相同,型腔尺寸必须考虑不同橡胶的收缩率,在产品尺寸基础上进行放大或缩小,方可得到合适的产品尺寸。模具从工艺操作考虑还要设置流胶槽、启模口、定位销等。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条