1) curved to cut out of shape
弯剪变形
2) bending deformation
弯曲变形
1.
Numerical simulation of the bending deformation of a casing;
井下套管弯曲变形的数值模拟
2.
Calculation of bending deformation of beam(plate) considering geometric nonlinearity;
考虑几何非线性时梁(板)的弯曲变形计算
3.
The bending deformation of the aspherical bending lapping tool under the action of bending moment was analyzed according to its deformation feature in high speed lapping process.
针对高速研磨加工中使用的弯曲成型法非球面磨具的变形特点,分析了磨具在弯矩作用下产生的弯曲变形,指出磨具高度对磨具成形误差影响较大,磨具宽度对其影响较小。
3) bending deflection
弯曲变形
1.
The paper comprehensive study three respects: the influence upon bending deflection caused by three primary aspects such as gravity,pull of the mouth of well and rotate speed of drillstring.
综合考虑了钻柱的重力、井口部的提升力及钻柱的转速等三个主要方面对钻柱弯曲变形的影响,建立了动力学模型和方程,并以实例验证了本研究方法的可靠性。
2.
For resolving the problem of bending deflection of overhang shaft,it is macroprogram that is applied to compensate the errors of machining deflection timely.
为了解决悬伸轴较大的弯曲变形问题,应用宏程序编程适时补偿切削变形误差,从而获得较高的加工精度,并能提高效率,降低成本,达到了预期的目的。
3.
The calculation of bending deflection is always required in analyzing stiffness of the continual beams.
工程实际中,常采用各种形式的连续梁,对连续梁进行刚度分析时,需要计算其弯曲变形。
4) cold-bending forming
冷弯变形
1.
,Ltd by breaking through traditional cold-bending forming change on OD 114 mm high frequency welded pipe units.
上海申花钢管有限公司在114高频焊管机组上突破传统冷弯变形方法,设计出强力焊管。
5) deformation
[英][,di:fɔ:'meɪʃn] [美]['difɔr'meʃən]
弯曲变形
1.
A study on bend deformation equation of ring elastic slice and solution;
环形弹性阀片弯曲变形曲面方程及其解
2.
Several ways to reduce deformation are proposed.
分析了 YG6长条薄片生产过程中弯曲变形的影响因素 ,提出了几种抑制弯曲变形的方法。
3.
Based on the mechanics model of ring throttle slice of telescopic shock absorber on a linear pressure, by the boundary constraint and deformation continuity condition, the general solution of differential equation of throttle slice deformation was got, and with mathematical transform, the analytic formula of throttle slice deformation was established.
根据减振器环形节流阀片线性非均布力学模型,利用节流阀片的边界约束条件和连续性条件,得到环形阀片弯曲变形曲面微分方程的通解,然后通过恒等变换,建立了环形节流阀片在线性非均布载荷作用下的弯曲变形系数和弯曲变形解析计算式。
6) bending distortion
弯曲变形
1.
The results show that the overbending distortion of the broach can be avoided by straightening and special tool fixed tempering after marquenching.
分析了W 18Cr4V高速钢拉刀的热处理工艺特点和变形问题 ,认为拉刀采用分级冷却后先校直再用工具固定回火的工艺 ,可解决拉刀弯曲变形超差的质量问
2.
The new and the traditional techniques of rectifying bending distortion with flame areapplied to rectify the bending dstortion of bead welding of the steel plate edge and the Tee-beamtest piece.
采用火焰矫正弯曲变形的新旧两种工艺对板边堆焊试件和T型梁试件进行了弯曲变形的矫正，通过两种工艺矫正弯曲变形矫正量的测试和比较，以及对堆焊试件应力的测试和分析，探讨了火焰矫正弯曲变形新工艺的特点及原理。
3.
Reactors used in chemical industry must satisfy rigidity requirements to ensure the bending distortion to be controlled within the tolerated range as well as strength requirements to prevent breakage.
化学反应器不仅要满足强度条件,以保证在使用中不发生断裂破坏;也要保证刚度条件,使设备在正常操作时的弯曲变形不超过规定的许可范围。
补充资料：胎圈变形、弯钢圈、钢圈变形、口弯等
分子式：
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
CAS号：
性质：又称胎圈变形、弯钢圈、钢圈变形、口弯等。指轮胎胎圈表面局部高低不平的现象。 胎圈底部 bead base 又称胎圈基部。指轮胎与轮辋胎圈座接触的部位。其作用是保持胎圈与轮辋底部相着合。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条