1) the supercritical turbine
超临界/超超临界汽轮机
2) ultra supercritical steam turbine
超超临界汽轮机
1.
Orthogonal test method was used to optimize heat treatment process of the heat-resistant steel ZG1Cr10MoWVNbN for ultra supercritical steam turbine.
采用正交试验方法研究了超超临界汽轮机用耐热钢ZG1Cr10MoWVNbN的热处理工艺,分析了正火温度、保温时间和回火温度三个主要因素对该钢组织和性能的影响规律,对其热处理工艺进行了优化。
2.
The paper describes the reason why the 1000MW ultra supercritical steam turbine with HP single bypass valve using HP casing start-up was not applied with HP exhaust non-return valve and introduces the methods to prevent over-speed for load rejection,HP casing overtemperature and water admission.
论述了采用高压缸启动方式的带高压一级旁路的1000MW超超临界汽轮机不设高排逆止门的依据及其防止汽轮机甩负荷超速、高缸超温与进水的方法:一是在高压导汽管上加装通风阀,二是在冷再管上加装通往凝汽器的排汽管,三是在冷再管的低位加装能显示水位、自动报警及自动疏水的疏水罐。
3.
Using FEM to model the rotor system of ultra supercritical steam turbine,treating the rotating rotor and static bearing-foundation as a coupling whole,the program is compiled.
考虑汽流激振的超超临界汽轮机转子系统的稳定性分析是个较新的课题。
3) ultra-supercritical steam turbine
超超临界汽轮机
1.
Thermal stress monitoring & control in 1000 MW ultra-supercritical steam turbine
1000MW超超临界汽轮机热应力监测及自动控制
2.
Application of rapid-cooling systems of Simens 1 000 MW ultra-supercritical steam turbines
西门子1000MW超超临界汽轮机快冷系统的应用
3.
With inlet temperature of ultra-supercritical steam turbine up to 600/620"C,the high-temperature component design has become a major issue.
随着超超临界汽轮机进汽参数达到600/620℃,高温部件已经成为汽轮机设计中的重要难点。
4) ultra-supercritical steam turbine
超(超)临界汽轮机
5) supercritical turbine
超临界汽轮机
1.
An analysis has been carried out on causes leading to steam leakage from the reheating main steam valve s stem of a 600MW supercritical turbine unit, based on which the leakage problem was successfully solved without dismantling the valve stem,thus accumulating some experience for treating similar problems.
对某600 MW超临界汽轮机再热主汽阀阀杆漏汽的原因进行了详细分析,并在不拆卸阀杆的情况下成功消除了漏汽现象,为处理此类问题积累了经验。
2.
The original governor system of 500 MW supercritical turbine in Tianjin Guohua Panshan Power Generation Co.
天津国华盘山发电有限责任公司500 MW超临界汽轮机原系统属于电液联合控制,其系统功能和控制精度均存在不足。
3.
This paper explains the structure characteristic of 600MW class supercritical turbine,illustrates its thermal expansion system and start-up feature etc.
分析了600MW等级超临界汽轮机的结构特点,阐述了机组的滑销系统和启动特点等,总结了超临界汽轮机的总体特点,并对改进和创新的一系列机组进行了论述。
6) supercritical steam turbine
超临界汽轮机
1.
Causal analysis of abnormal start-up of oil drivers for steam inlet valves of 600 MW supercritical steam turbines and relevant treatment;
600 MW超临界汽轮机进汽阀油动机异常开启的原因分析及处理
2.
Development of supercritical steam turbine with 9Cr steel materials;
超临界汽轮机用9Cr钢材料开发
3.
As the inertia moment of supercritical steam turbine is large,and the time constant of rotor speedup is small,the overspeed protection system is very important for unit itself.
超临界汽轮机转子由于转动惯量大,转子飞升时间常数小,所以对它进行超速保护尤为重要。
补充资料：马超(176～222)
三国时期蜀国将领。字孟起，扶风茂陵（今陕西兴平东北）人。父马腾与韩遂等于汉灵帝时起兵割据凉州。后因内部矛盾,马腾复归汉,至京师任卫尉，马超因领其众,为偏将军，甚得羌、胡等族人心。建安十六年(211)曹操西征关陇,马超与韩遂等关中割据势力屯据潼关,联合抵抗，曹操施离间计，致使马、韩相互猜疑，遂一举击败。马超率羌、胡退出关中，转战陇上攻陷冀城，杀凉州刺史，并其众，自称征西将军，督凉州军事。不久原刺史故吏杨阜起兵讨伐，杀其妻子,马超投奔汉中,依其地割据势力张鲁，不得志。建安十九年，归刘备。时刘璋被刘备围于成都，马超率军抵城下，城中震怖，加速了刘璋覆败。诸葛亮赞他文武全才，勇猛过人。建安二十二年，刘备率军进攻汉中,马超从征。二十四年,刘备为汉中王,拜马超为左将军,假节;章武元年(221)，迁骠骑将军，领凉州牧。次年卒。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条