说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 耦合路径
1)  coupling paths
耦合路径
1.
The DM EMI excitation source generated by power electronic switches and coupling paths is analyzed.
为研究挂接单个三相逆变器的直流电网的差模传导干扰,分析了干扰源和耦合路径并建立了差模传导干扰的频域等效电路,在10 kHz~30 MHz频率范围内分析了实验测得的相关器件参数。
2)  path coupling
路径耦合
1.
A dynamic corporate firm model was developed for differential games, with the Maximum Principle of Pontryagin combined with the path coupling procedure of van Loon to analyze the coordinating and adapting processes of the firms in games.
借鉴微分对策的思想 ,结合最优控制理论中 Pon-tryagin极大值原理和 van L oon路径耦合方法 ,研究了两家股份制企业之间不断协调和相互适应的博弈过程 ;突破了传统 Cournot模型只能进行均衡分析的局限性。
3)  cross-coupling path
交叉耦合路径
4)  coupling paths
耦合途径
1.
In this article, we make research on the process of automatic control system of papermaking, analyze the main interference,coupling paths and harmfulness that produce great effect on control system, and promote effective anti interference method.
本文以造纸生产线中自动控制系统的干扰问题作为研究对象,分析给系统带来干扰的主要形式、耦合途径和危害性,并提出有效的抗干扰措施。
2.
The main ways,the coupling paths and the harmfulness of the interference,which produced great effect on the controlling system,were analyzed.
以造纸生产线中自动控制系统的干扰问题作为研究对象 ,分析了给系统带来影响的干扰的主要形式、耦合途径和危害性 ,并提出了有效的抗干扰措
5)  coupling path
耦合途径
1.
The subject is supported by Science and Technology Committee of Tianjin(05YFSYSF033), and the paper mainly studies around three elements of the electromagnetic disturbance which are disturbance source、coupling path and sensitive equipment, and focuses on radiation disturbance characteristics of measuring apparatus, and illustrates the suppression technologies.
本文对电磁兼容的发展现状及内容进行了研究,讨论和分析了常见电磁骚扰源的特性及其耦合途径,并重点阐述了传导耦合、共阻抗耦合、感应耦合和辐射耦合的特性,为分析实际产品的电磁兼容性问题奠定了理论基础。
6)  aperture-coupled
口径耦合
1.
Study on Aperture-coupled Microstrip Antenna Based on FDTD Method;
基于时域有限差分法的口径耦合微带天线的研究
2.
To increase the radiation efficiency and broaden the operation bandwidth, an aperture-coupled microstrip antenna of high temperature superconductor with multi-layer substrates is designed.
为提高辐射效率和扩展工作带宽,对一种口径耦合馈电的多层介质高温超导微带天线进行了设计。
3.
It is an aperture-coupled antenna with four layers and has the advantages like lightweight and thin profile.
天线印制板为四层结构,通过口径耦合馈电,体积小,重量轻。
补充资料:Pro/ENGINEER中复杂几何路径的数组阵列
 

1 引言



    Pro/ENGINEER是目前应用非常广泛的CAD/CAM软件,其功能非常强大。在Pro/ENGINEER中进行特征复制时, PATTERN(数组阵列)可以一次建立多个相同的特征,比COPY(复制)省时省力。



    在实际应用中,阵列的几何路径有规则的(如直线形、圆形等),也有不规则的(如平行四边形、椭圆形等)。对于规则路径,其生成较简单,如圆形路径,选取一周向驱动尺寸,输入阵列的增量与个数即可。下面以在基座上钻孔为例,介绍不规则几何路径的数组阵列。



2 设计实例



    首先,生成基座(如图1黑点表示孔的圆心位),其中心点位于Pro/ENGINEER中坐标系的原点,再钻出左上角的第一个孔(以基座的两条边为参考边,这两条边的交点为准原点)。然后进行数组阵列,产生其余的孔,依次选择“Pattern→General→Table”。





图1 黑点表示孔的圆心位



2.1 步骤一



    选择图1中的尺寸“40,55”作为“表格驱动阵列的驱动尺寸”,然后选“Done”。



2.2 步骤二



    选择“Add”,进行表的添加(输入一个表名如A),接着打开一个窗口,其中已有的文字均为注释语句,最后一行为:



    idx       d4(40.0)     d3(55.0)



    其中,idx表示这一列填的是序号,从1开始;d后的数字以实际操作中产生的为准,括号内数值为步骤1中所选驱动尺寸的值,可以看出该值的显示顺序与尺寸的选择顺序是对应的。



2.3 步骤三



进行表的录入,依次填入:
1 65   55
2 90 55
3 115 55
4 140 55
5 50 85
6 60 115
7  70 145
8 95 145
9 120 145 
10 145 145  
11 170 145
12 150 85
13 160 115



    其中1~4为上部右边的4个孔,5~7为左边3个孔,8~11为下部右边4个孔,12~13为右边剩余2个孔。



2.4 步骤四



    首先点击“File→Save”,并且进行保存。然后点击“File→Exit”,退出程序。之后执行“Done”即可进行阵列,如图2所示。


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条