1) active Miller clamp
有源密勒箝位
1.
The aim of this paper is to discuss new solutions in the design of insulated gate bipolar transistor (IGBT) gate drivers with advanced protections such as two-level turn-on to reduce peak current when turning on the device, two-level turn-off to limit over-voltage when the device is turned off, and an active Miller clamp function that acts against cross conduction phenomena.
论述了IGBT门极驱动器设计新方案,它具有先进的保护功能,如元件采用双电平开通以减小峰值电流,采用双电平关断以限制过电压,以及防止出现桥臂贯通的有源密勒箝位。
2) active clamped
有源箝位
1.
The zero-voltage soft-switching technology of active clamped single end forward inverter;
有源箝位单端正激零压软开关技术
2.
Optimizing design of main magnetic devices in an active clamped forword converter;
有源箝位正激式变换器磁性元件的优化设计
3.
The method to symmetrically magnetic reset the power transformer with the Boost active clamped circuit and to achieve zero voltage switching through the resonant excitation of power switches parasitic capacitance and inductance is discussed.
本文对升压式有源箝位零电压开关正激变换器的工作过程进行了分析。
3) active clamp
有源箝位
1.
Study of an active clamp forward-flyback converter;
一种有源箝位正反激变换器的研究
2.
Research on active clamp Zero-Voltage-Switching forward converter;
有源箝位ZVS正激变换器的分析研究
3.
Dual switch forward converter with zero voltage switch active clamp;
一种零电压开关有源箝位双管正激变换器
4) active-clamp
有源箝位
1.
The Research on the Bias of Magnetizing Current in Active-clamp forward Converter;
有源箝位正激变换器中励磁电流直流偏置问题的研究
2.
In order to achieve Zero Voltage Switching (ZVS) easier for both primary switch and auxiliary switch in the active clamp forward converter,an improved active-clamp ZVS forward converter topology is proposed in this paper.
在有源箝位正激电路中,为了使主开关管和辅助开关管能较容易地实现零电压开通条件,提出了一种改进型有源箝位正激拓扑方案。
3.
For the active-clamp ZVS-PWM forward converter,the reset of the transformer is the most crucial technique.
在有源箝位ZVS-PWM正激变换器中,变压器的磁复位技术是其中最关键的一项技术。
5) Active clamping
有源箝位
1.
To briefly introduce the operating mechanism for the soft switch of the active clamping and forward and flyback combination of ZVS-PWM with the single-end circuit topology.
简要介绍一种有源箝位、正反激组合ZVS-PWM单端电路拓扑的软开关工作形成机理。
6) active-clamping
有源箝位
1.
Analysis and design of interleaving ZVS-PWM active-clamping forward converter;
交错并联有源箝位ZVS-PWM正激变换器的分析与设计
2.
This paper presents a kind of drive circuit for active-clamping synchronous rectification.
介绍了一种适用于有源箝位同步整流的驱动电路,它适用于输出电压和功率密度较高的场合。
3.
A novel active-clamping circuit used for boost converter is proposed.
提出了一种应用于Boost变换器的新型有源箝位电路。
补充资料:密位制
以密位为单位来量角的制度。把圆周6000等分,每一等分的弧所对圆心角称为1密位的角。密位的写法是在百位数字与十位数字之间画一条短线,如15密位记为“015”,1370密位记为“1370”。角度制和密位制的换算关系是:1密位=3′36″,1°≈167密位。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条