1) failure standard value
![点击朗读](/dictall/images/read.gif)
破坏标准值
2) damage standard
![点击朗读](/dictall/images/read.gif)
破坏标准
1.
According to features of underground chamber of a hydropower station,its damage standards of blasting vibration are given.
根据该水电站地下洞室的特点,提出了爆破振动破坏标准,得到了地下洞室新浇混凝土支护区爆破安全控制参量。
2.
According to features of underground chamber of Qiaoqi hydropower station,damage standards of blasting vibration based on the blasting safety control and parameters of new cast-in-situ concrete of the underground chamber are gained.
根据国家爆破安全规程及国内外研究成果,通过对硗碛水电站地下厂房母线洞爆破进行振动测试,采用萨道夫斯基公式回归出该地形地质条件下的爆破衰减规律,并结合该水电站地下厂房开挖的特点,提出了爆破振动破坏标准,得出了岩锚梁新浇混凝土区爆破安全振动控制参量,并提出了相应的爆破降振措施,将该措施和控制参量应用到后期的爆破开挖中,从后期的监测数据和工程实践来看,研究成果得到了很好的应用,保证了工程爆破的安全顺利施工。
3.
According to the features of underground chamber of a hydropower station,its damage standards of blasting vibration are given.
根据该水电站地下洞室的特点,提出了爆破振动破坏标准,得出了地下洞室新浇混凝土支护区爆破安全控制参量,分析了爆破地震与天然地震的不同特点,并结合该水电站地下洞室的爆破实际,提出了相应的爆破降震措施。
3) failure criterion
![点击朗读](/dictall/images/read.gif)
破坏标准
1.
Discussion on the failure criterion of float resisting anchor rod test;
![点击朗读](/dictall/images/read.gif)
关于抗浮锚杆试验破坏标准的讨论
2.
Firstly,the material will be in failure when the compressive strain reaches 5%,which can be considered to be a suitable dynamic failure criterion of LCES,and then the effort is focused on the confining pressure,cement content and EPS content effect on the dynamic strength properties of LCES.
首先确定压应变达到5%是适合LCES的动力破坏标准,然后着重研究围压、水泥含量和EPS掺入比对LCES动强度特性的影响。
3.
The expression of general strain failure criterion is recommend.
![点击朗读](/dictall/images/read.gif)
以此为基础,综合考虑剪切变形和正向偏差变形的共同效应,同时为了能够反映平均残余变形和循环变形的影响,建议了一个综合应变破坏标准的算式。
4) standard rate of collapse
![点击朗读](/dictall/images/read.gif)
标准破坏率
5) standard of destroyingment judgement
![点击朗读](/dictall/images/read.gif)
破坏判断标准
6) standard for safety warning
![点击朗读](/dictall/images/read.gif)
破坏预警标准
补充资料:平均值-标准值控制图
分子式:
CAS号:
性质:平均值和标准差控制图的一起使用,简记为x-s图。前者用来判断产品质量特性量值的平均值是否处于或保持所要求的水平,后者用来判断产品质量特性值的标准差是否处于或保持所要求的水平。
CAS号:
性质:平均值和标准差控制图的一起使用,简记为x-s图。前者用来判断产品质量特性量值的平均值是否处于或保持所要求的水平,后者用来判断产品质量特性值的标准差是否处于或保持所要求的水平。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条