1) king diameter coupling bolt
大直径联接螺栓
1.
A new method of pre-tightening by means of drilling and heating for the king diameter coupling bolt was introduced.
介绍了一种在大直径联接螺栓中心钻孔,通过加热对螺栓进行预紧的新方法。
2) large diameter bolt
大直径螺栓
1.
Experimental study on bi-directional charging explosion for cutting large diameter bolts;
双向线型聚能爆炸切割大直径螺栓的试验研究
2.
M42 large diameter bolts were used in hydraulic damp bases of its main bridge as wind-resistant and anti-seismic specimens.
武汉天兴洲公铁两用长江大桥正桥液压阻尼支座采用M42大直径螺栓防风、抗震并作为钢梁架设过程中的纵向约束。
3) Connecting bolt
联接螺栓
1.
This paper analyses the working state of E line up crane beams and connecting bolt in the whole mould wrokshop by means of testing and finite element methods.
利用测试手段和有限元计算对整模车间Ｅ列吊车梁及联接螺栓的工作状态进行了分析，找出梁间联接螺栓的破坏原因，并提出改进方案，为保证吊车梁正常运行提供了科学依据。
4) Bolt Connection
螺栓联接
1.
Simply and easy method named check table method in design of tightened bolt connection with uncontrolled tightened force is presented.
针对不控制预紧力的紧螺栓联接设计计算时需采用试算法的问题,提出一种无需试算的新方法即查表法。
2.
The stress and strength of bolt connection are analysed,and some problems which must be considered in structure design are raised.
介绍了某型舰上A型、B型和C型雷达的天线基座与桅杆支座的联接方式,对螺栓联接的受力情况及其强度作了分析,提出结构设计中需要考虑的一些问题。
3.
The paper provides some valuable references and is useful for engineers and technicians on the basis of analysis of problems needing attention in the design of bolt connection.
对螺栓联接设计中应注意的主要问题进行分析,提供了一些有价值的资料,对工程技术人员合理设计螺栓有一定参考作用。
5) bolt joint
螺栓联接
1.
Strength analysis of rivet and bolt joint structure in aluminum alloy car body of high-speed train;
高速列车铝合金车体中铆钉和螺栓联接结构的强度分析
2.
Stress calculations for bolt joint structures by applying FEM;
应用有限元技术计算螺栓联接的方法研究
6) Bolt coupling
螺栓联接
1.
According to the theory of mechanial reliability design,discussutility computed methods of reliability design of bolt coupling,to give design compte formula and steps of reliability design of bolt coupling,and selection of principal parameter was conducted experiment study.
论述了螺栓联接的可靠性设计实用计算方法，给出了螺栓联接可靠性计算公式和设计步骤，并对主要设计参数的选择进行了实验研究分
2.
In this paper, the dynamic models of bolt coupling with washeris founded on the basis of several hypotheses, and is analysedwith the dynamics theory.
本文根据几个假设，建立了带弹簧垫圈的螺栓联接的力学模型，并用有关力学理论对模型进行了分析，给山了采用弹簧垫圈能提高联接的疲劳强度，但不利于联接的可靠性和防松的解析证明。
补充资料：当量比表面直径、表面积体积平均直径
分子式：
CAS号：
性质：又称当量比表面直径、表面积体积平均直径。是颗粒群表面积分布的平均直径。其意义为与颗粒群的粒形相同，总体积相同、总表面积相同，且粒度均匀的一个假想颗粒群的粒度。亦即指与该颗粒群的粒形相同，比表面积相同的一个颗粒的粒度。
CAS号：
性质：又称当量比表面直径、表面积体积平均直径。是颗粒群表面积分布的平均直径。其意义为与颗粒群的粒形相同，总体积相同、总表面积相同，且粒度均匀的一个假想颗粒群的粒度。亦即指与该颗粒群的粒形相同，比表面积相同的一个颗粒的粒度。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条