1) shrinkage
[英]['ʃrɪŋkɪdʒ] [美]['ʃrɪŋkɪdʒ]
尺寸收缩
1.
Although the structure of automotive starter fork-lever was simple,large amout of failed parts emerged due to the uncertain shrinkage and weak strength.
汽车起动机齿轮拨叉的结构简单,但注塑成型时因尺寸收缩和强度等问题产生大量的废品。
2) Dimensional Contraction Rate
尺寸收缩率
1.
Effects of Centrifugal Forces on Porosity and Dimensional Contraction Rate of TC4 Alloy Castings
采用真空石墨型立式离心铸造方法,研究了离心力大小对Ti-6Al-4V(TC4)钛合金铸件内部孔洞率以及铸件宏观尺寸收缩率的影响。
3) dimension swelling and contracting
尺寸涨缩
1.
The evaluation of quenching medium characteristies and the influence of operating temperature on the dimension swelling and contracting and deformation were introdced,the effects of quenching medium characteristics and operating temperature during the heat-treatment of bearing parts were showed,so that the evedence was given for selecting quenching medium and reducing finishing allowance of parts.
探讨了淬火介质特性评价及使用温度对套圈的尺寸涨缩及变形的影响,体现了淬火介质特性及使用温度在轴承零件热处理过程中所起的作用,为淬火介质的选用和减少零件的加工留量提供依据。
4) size reduction
尺寸缩减
5) scaling
[英]['skeiliŋ] [美]['skelɪŋ]
尺寸缩放
1.
This paper presents mainly the algorithms used in a video format conversion SoC, including weighted sum motion-adaptive de-interlacing algorithms, multi-level pipelined filtering algorithm used in scaling and DDA algorithm.
给出了实现视频格式转换SoC芯片所需的各部分算法:去隔行部分的加权运动自适应算法,尺寸缩放的多级缩放流水线滤波算法,帧频变换的DDA(Digital Differential Analyzer)算法。
2.
Prototype Design of Algorithms, Used in a VFC Chip and RTL Implementation Its Scaling Module;
本文作为天津市科委重点科技攻关项目-视频格式转换芯片的研究的一部分,其主要目标是提出一组视频芯片处理算法及算法C原型和其中的尺寸缩放算法的RTL实现。
6) reduction in size
尺寸缩减
1.
Both experimental and numerical results show that the two kinds of antennas both have the characteristics of reduction in size and the tree-like fractal monopole also has multiband behavior.
文中对Koch分形单极子和树状分形单极子的输入阻抗特性和方向图特性进行了分析，数值结果和测量数据都表明这两种分形天线具有尺寸缩减性，而且树状分形单极子还具有多波段特性。
补充资料：工程图标准尺寸及坐标尺寸
标准标注类型，是我们常用的标注类型。而坐标标注是便于数控加工采用的另一中标注形式。PRO/E可以将两种标注方式进行转换。
· 3.2 标准标注到坐标标注的转换
注意： 转化为坐标标注的尺寸必须是线性标注的，下列尺寸不能转化为坐标标注：
- 被显示成线性尺寸的直径
- 中心线尺寸
- 选择MODIFY DRAW > Dim Params > Dim Type > Ordinate Dim > Create Base.
- 选择作为参考基准线的尺寸
- 选择基准的引出线，该点为0点
- 选择 MOD DIM TYPE > Lin to Ord .
- 选择线性尺寸：注意：必须选择具有相同基准的尺寸
========>>>>
1. 选择 DIM PARAMS > Diam Dim Type .
2.点击Ord to Lin 
3.选择尺寸即可
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条