1) fullness ratio
充水率
1.
Experimental research of maximum allowable fullness ratio (α) of plastic drainage stack;
塑料排水立管最大允许充水率α值的试验研究
2.
Application Enforcement of the plastic drainage pipes had to stablish the theory for estimating of the maximum discharge capacity of the plastic drainage stack in building and the core issue of the theory was to determining of the maximum allowable fullness ratio of the plastic stack.
塑料排水管的大力推广与应用必须解决塑料排水立管的最大通水能力这一理论问题，而解决这一问题的关键在于确定塑料排水立管最大允许充水率α值。
3) controlled water
充水
1.
The quantitative relationship of the forecast to differential settlement of annular wall foundation of controlled water tests to preload large oil tanks is reserched and expounded briefly.
对大型油罐软弱地基充水预压试验中环墙基础不均匀沉降预测的定量关系作研究和简述 ;根据实测沉降资料 ,采用回归分析 ,提出了预测关系式 ,并对预测的主要影响因素作了具体分析。
4) Water-filling
充水
1.
Base on the Saint-Venant equation and priessmann difference,a mathematical model which a- dopted virtue discharge method and slot method for simulating continuous water-filling in Long-distance water transfer system is build.
本文在圣维南方程基础上,采用假想窄缝法和虚拟流量法,并运用稳定性高的 Priess- mann 隐格式建立长距离串联输水管线的连续充水数学模型。
5) water filling source
充水水源
1.
Based on comprehensive analysis of Taiping coalmine hydrogeological condition and water outlet lithologic characteristics,through contrastive analysis of borehole water prospecting drainage and water sample tested data considered that the indirect water filling source of +700 level belt inclined winze may come from Mosuo River.
在综合分析太平煤矿井水文地质条件、出水点岩性特征的基础上,通过钻孔探放、水样化验资料的对比分析,认为该矿+700水平胶带暗斜井的间接充水水源可能来自摩梭河;基于涌水点位置与出水量,以及瞬变电磁法确定的巷道前方富水区域情况,确定了采用浅层注浆法封堵的治水方案。
2.
After analyzed the hydrogeological data from Baibu minefield,considered that the water filling sources of shallow part Nos.
通过对白布井田水文地质资料的分析研究,认为浅部6上、6中、7号煤层开采时充水水源为顶板进水的长兴组岩溶裂隙水、含煤地层裂隙水、滑坡体中的孔隙水;充水通道主要为裂隙、岩溶管道、导水裂隙带、断层带。
6) Filling rate
填充率
1.
Under the condition of DO of 4 to 5 mg/L in HSMBR and HRT of 4 h,the COD removal rate is 75%,62% and 56% respectively when the carrier filling rate.
在HSMBR中的溶解氧浓度为4～5mg/L、HRT为4h的条件下,当填料填充率分别为45%、20%和0时,系统对COD的去除率分别为75%、62%和56%;对NH3-N的去除率>90%;膜清洗周期分别为40、36和24d。
2.
The elongation and filling rate have been selected and the tensional coefficient has been calibrated systematically on the bases of the rolling law.
根据轧制规律,选用合理的延伸系数和填充率,系统地校核了张力系数,减少了断锭堆料事故,改善和提高了铝杆的力学性能,延长了轧辊使用寿命,降低了产品的制造成本。
3.
In order to model the estimation for the over-sample and sub-pixel imaging considering the detector s filling rate,the detector pixel spread function is derived adversely by the sub-pixel arithmetic.
针对探测器存在填充率时过采样和亚像元成像质量评价问题,利用亚像元算法反演线阵探测器像元扩散函数,发现较过采样成像不仅能在1/m微扫描作用下减小采样间隔,还能使探测器矩形窗口压缩m倍。
补充资料：充炭黑充油丁苯橡胶
分子式：
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
分子量：
CAS号：
性质：同时含有炭黑和油的丁苯橡胶。性能和用途与充炭黑丁苯橡胶和充油丁苯橡胶相似。由冷聚丁苯胶乳与炭黑的水分散液和油乳液经混合、凝聚、洗涤、过滤、干燥等步骤制得。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条