说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 电距离
1)  Electric distance
电距离
2)  distance of electrodes
电极距离
3)  creepage distance
爬电距离
1.
Determination of the minimum clearance and minimum creepage distance for electronic equipment in safety examinations;
电子产品检测中电气间隙和爬电距离的确定
2.
The determination method of electrical clearance and creepage distance is expounded, and the testing and demonstration method is described.
阐述了电气间隙和爬电距离的确定方法,并介绍了试验验证方法。
3.
Calculation and numerical analysis from programming educesaccurate measurement of creepage distance in complicated structure, thereby strengthening the proficiency test ability.
电距离是安全试验和国内外水平测试的重要项目。
4)  electromechanical distance
机电距离
1.
A new dynamic equivalence method based on the electromechanical distance is presented.
该方法根据系统各单元间机电距离的量化指标,应用离差平方和方法对初始系统进行聚类分析;然后根据聚类结果将系统划分成内、外部子系统,并对外部系统进行参数等值,得到与初始系统等价的简化系统。
5)  electrical distance
电气距离
1.
The shortcoming of traditional definition of electrical distance recently used in power network partitioning for secondary voltage control is discussed.
首先分析了现有电气距离定义在无功电压控制分区研究中的不足,通过考虑PV节点准稳态物理响应的灵敏度计算,构造了无功源控制空间。
2.
The concept of network partitioning using “electrical distance” is applied to reactive power allocation.
将电力系统分区的思想应用于电力系统无功配置,给出了利用"电气距离"进行分区的方法,提出了结合电力系统分区与灵敏度分析来确定无功源最佳配置地点的一整套方法。
3.
The concept of electrical distance is introduced to partition a power network into strongly connected sub networks.
结合电力系统分区与电压稳定灵敏度分析确定无功电源最佳配置地点的方法 ,将电力系统分区的思想应用于电力系统无功配置 ,利用“电气距离”把电力系统分成几个耦合强的小区。
6)  power supply distance
供电距离
补充资料:厂用电受电


厂用电受电
energizing of auxiliary power system

chongyongd一on sho一Jd一on厂用电受电(energizing of auxiliary powersystem)机组附属设备安装完毕后需通电试运行,所需厂用电源由外部供给,因此厂用电受电是调试工作开始的标志。 受电步骤新建电厂先由电力系统向变电站供电,再依次对高压起动/备用变压器、3~10kv厂用配电装置、厂用工作变压器及380V配电装置供电。扩建电厂因高压起动/备用变压器已经投人运行,故可利用它的电源对扩建的厂用配电装置等供电。 调试项目主要有:①用额定电压依次对空载线路、变电站母线、隔离开关、断瘩器、互感器、变压器及厂用配电装置等进行冲击合闸试验。有条件时.冲击合闸前应先进行递升加压试验。升压过程中注意检查各设备有无放电声及短路现象,发现问题及时处理后再进行升压。②检查三相电压应平衡,相序应正确,各段母线的相位彼此应一致。对配电装置供电时,有时会由于母线电容和与母线连接的电磁式电压互感器的电感相互作用而出现铁磁谐振,此时相电压升高,中性点明显位移。为消除谐振可在电压互感器的剩余电压绕组处并联电阻以去振。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条