1) MoS2 micro-spheres
二硫化钼微球
1.
Results show that MoS2 micro-spheres product is well modified by extractant and is a much better extreme-pressure additive and anti-wear and friction-reducing additive in 500SN than CC-MoS2.
将自制的表面修饰的二硫化钼微球(MS-MoS2)和商业级胶体二硫化钼(CC-MoS2)分别添加到基础油500SN中,用四球摩擦磨损机和SRV微动摩擦磨损试验机对比研究了不同润滑体系的极压性能和抗磨减摩性能。
2) MoS_2
二硫化钼
1.
Study of the Tribological Behavior of Kaolinite Based Geopolymer Composites Filled with MoS_2;
二硫化钼填充高岭土基矿物聚合物复合材料的摩擦学性能研究
2.
Study on the Friction and Wear Properties of Polyimide Composites Filled with Polytetrafluoroethylene and MoS_2;
聚四氟乙烯和二硫化钼填充聚酰亚胺复合材料的摩擦磨损性能研究
3.
TRIBOLOGICAL PROPERTIES OF HYBRID CARBON FIBER AND MoS_2 REINFORCED POLYAMIDE 1010 COMPOSITES;
碳纤维和二硫化钼混杂增强尼龙复合材料的摩擦学性能研究
3) MoS2
二硫化钼
1.
Study on the Surface Oxidation Behaviour of MoS2(Ⅱ) Oxidation and Electron Transfer on the Friction Surface of MoS2;
二硫化钼表面氧化行为的研究（Ⅱ）─—二硫化钼摩擦表面氧化与电子转移的研究
2.
Three methods,the electrophoresis aggradation,brushed coating and water cooking method were presented to deposit MoS2 coatings in the material surfaces,and the deposited mechanisms were analyzed.
选用电泳沉积法、刷涂法和水煮法3种方法在材料表面制备了二硫化钼涂层,并探讨了3种方法形成涂层的机制。
3.
UNMWPE composites filled with nano-meter SiC, microfine glass bead, MoS2 and other fillers separately were prepared by means of in-situ polymerization and the properties of the composites were test.
用原位聚合法制备了分别加入纳米碳化硅、玻璃微珠、二硫化钼等填料的超高摩尔质量聚乙烯复合材料, 测试了其性能,并对原位聚合法和共混法的复合材料材料性能进行了对比。
4) molybdenum disulfide
二硫化钼
1.
Influence of molybdenum disulfide on properties of NBR compound;
二硫化钼对NBR胶料性能的影响
2.
Research on preparation of molybdenum disulfide nanoparticles by homogeneous precipitation method;
均匀沉淀法制备纳米二硫化钼粉末的研究
3.
Study of Preparation of Fined Molybdenum Disulfide Powder by Ball Milling;
球磨细化二硫化钼粉末的试验研究
6) Molybdenum sulfide slabs
硫化钼微晶
补充资料：可降解淀粉微球和生物降解白蛋白微球阻滞法
可降解淀粉微球和生物降解白蛋白微球阻滞法
介入放射学技术。介入性局部化疗之前，把二者注入靶动脉，可暂时减少动脉血流，再行化疗药物灌注，以减少血液冲刷，保持局部化疗药物浓度的技术。与其他中期和长期栓塞微球不同，DSM和BAM仅造成数十分钟的血流量减少，待其被降解后血流可恢复至以前水平。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条