说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 模型桩
1)  model pile
模型桩
1.
Experimental investigation on lateral load model pile in soft clay;
软粘土中水平荷载模型桩的试验研究
2.
Curves of low strain reflective wave method for model piles;
模型桩低应变反射波法曲线研究
3.
The dynamical testing for model pile is described.
通过动测桩身完整性模型桩模拟试验,获得了桩身典型缺陷与波形特征的对应关系,完善了动测桩基完整性的理论依据,并对桩基完整性检测技术提出了几点意见。
2)  pile-soil model
桩-土模型
3)  pile group model
群桩模型
4)  model of pile-soil
桩土模型
1.
This article analyzes the selection of the soil boundary in the model of pile-soil with finite element method,describes the modeling of the pile-soil in detail and presents the reasonable soil boundary of the pile-soil model used for the single pile loaded,on the basis of calculation of the ultimate bearing capacity of piles provided by various soil boundary ranges.
运用有限元软件对单桩受荷时桩土模型中土体边界的选取进行了分析。
5)  rigid pile model
刚性桩模型
1.
There are two mechanics models and corresponding calculation methods of embedding section of anchored slide-resistant piles,which were classfied into rigid pile model and elastic pile model according to the relative rigidity of pile-soil system.
传统上对于桩身嵌入段的计算,须根据桩身与桩周岩土的相对刚度划分为刚性桩和弹性桩两种不同的计算模型,并各自对应不同的算法及计算公式,通过对两种模型计算式的数学极限分析表明,刚性桩模型算式仅为弹性桩计算法中将嵌入段的桩身刚度取很大值下的特例,两种模型算法在力学本质上是统一的。
6)  elastic pile model
弹性桩模型
1.
There are two mechanics models and corresponding calculation methods of embedding section of anchored slide-resistant piles,which were classfied into rigid pile model and elastic pile model according to the relative rigidity of pile-soil system.
由锚索桩嵌入段分别按弹、刚性桩模型算式的位移、转角的对比分析可知,基于弹性桩模型计算出的锚索受力大于按刚性桩模型,以弹性桩模型进行锚索设计偏于安全,而嵌入段的换算长度取1。
补充资料:AutoCad 教你绘制三爪卡盘模型,借用四视图来建模型
小弟写教程纯粹表达的是建模思路,供初学者参考.任何物体的建摸都需要思路,只有思路多,模型也就水到渠成.ok废话就不说了.建议使用1024X768分辨率

开始
先看下最终效果




第一步,如图所示将窗口分为四个视图




第二步,依次选择每个窗口,在分别输入各自己的视图




第三步,建立ucs重新建立世界坐标体系,捕捉三点来确定各自的ucs如图




第四步,初步大致建立基本模型.可以在主视图建立两个不同的圆,在用ext拉升,在用差集运算.如图:




第五步:关键一步,在此的我思路是.先画出卡爪的基本投影,在把他进行面域,在进行拉升高度分别是10,20,30曾t形状.如图:




第六步:画出螺栓的初步形状.如图




第七步:利用ext拉升圆,在拉升内六边形.注意拉升六边行时方向与拉升圆的方向是相反的.
之后在利用差集运算





第八步:将所得内螺栓模型分别复制到卡爪上,在利用三个视图调到与卡爪的中心对称.效果如图红色的是螺栓,最后是差集




第九步:阵列




第10步.模型就完成了




来一张利用矢量处理的图片


说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条