1) ball screw spline
滚珠丝杠-花键轴
2) ballscrew
['bɔ:lskru:]
滚珠丝杠
1.
Study on the Installation Method of Ballscrews;
滚珠丝杠安装方式的研究
2.
Auxiliary Sustaining Device for Long Span Ballscrew
长跨距滚珠丝杠辅助支撑装置
3.
Technical Strategy of High-speed Ballscrew Units
滚珠丝杠副高速化的技术对策
3) ball screw
滚珠丝杠
1.
Injection mould with ball screw stripping and ball bearing and ta-pered wedge fixed-distance pull off mechanism;
带滚珠丝杠脱模及滚珠斜楔拉模定距装置的注射模
2.
Die Casting Die with Mechanism of Ball Screw and Gear for Automatic Screw Thread Unloading;
带滚珠丝杠齿轮自动脱螺纹机构的压铸模
3.
Analysis of Dynamic Characteristic of Ball Screw Feeding System Based on FEM;
基于FEM的滚珠丝杠进给系统动态性能分析
4) Ball screws
滚珠丝杠副
1.
Design And Implementation of Actuator Ball Screws Testing System;
舵机滚珠丝杠副测试系统的设计与实现
2.
Automation in choosing model of ball screws;
滚珠丝杠副的选型自动化
5) ball screw pair
滚珠丝杠副
1.
This paper raises a non-hydraulic system and full-electric controlled friction welder;this welder uses servo-motor for driving ball screw pair to exert friction pressure,and it can achieve continuous driven and inertial friction welding on equipment.
提出了一种无液压系统的全电控制的摩擦焊机,利用伺服电机驱动滚珠丝杠副实现摩擦压力的施加,可以在一台设备上实现连续驱动摩擦焊接和惯性摩擦焊接。
2.
The influence factors of ball screw pair friction moment are analyzed, and a method to measure the friction moment is given.
分析滚珠丝杠副摩擦力矩的影响因素,并给出一种测量摩擦力矩的方法。
3.
Taking the antenna pedestal of a certain shipborne radar as an example,this paper describes the reasonable application of ball screw pair to the stabilized platform of shipborne radar antenna pedestal,and gives its characteristics & relative calculation.
以某舰载雷达天线座为例,论述了滚珠丝杠副在其稳定平台中的合理应用,并给出滚珠丝杠副的特点及相关计算。
6) ball screw
滚珠丝杠副
1.
Technology named"theory of ball center"for ball screw manufacturing;
滚珠丝杠副制造中的“球心论”技术
2.
Development on measuring system for frictional torque of ball screw;
滚珠丝杠副摩擦力矩测量系统的研制
3.
Reasearch on static stiffness detecting system of ball screw based on STC89C52
基于STC89C52单片机的滚珠丝杠副刚度检测系统
补充资料：花键轴磨床
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
（一）加工精度 | 参照ZBJ55040-4 | ||||||
1、分度相邻允差（μm） | ＜4 | 4~6 | 6 | ＞6 | |||
2、分度累积允差（μm） | ＜10 | 16 | 16 | ＞16 | |||
3、键侧对轴线平行度（μm） | ＜10 | 10 | 10 | ＞10 | |||
4、相邻键侧间平行度（μm） | ＜10 | 10 | 10 | ＞16 | |||
5、小径的圆度Ra（μm） | ＜0.8 | 0.8 | 0.8 | ＞0.8 | |||
（二）自动化程度 | |||||||
1、数控装置 | |||||||
2、切入进给数控 | |||||||
（三）噪声dB（A） | ≤75 | 75~80 | 81~83 | ＞83 | |||
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条