1) strong connection
强连接
2) bonding strength
连接强度
1.
Effects of holding time on interface structure and bonding strength of brazed joint of hydrogenated TC4 titanium alloy;
保温时间对置氢TC4真空钎焊界面结构及连接强度的影响
2.
Interface structure and bonding strength of brazed joint of TiC cermet/steel;
TiC金属陶瓷/钢钎焊接头的界面结构和连接强度
3.
Through experiments with aluminous sheets,punch bonding mechanism and die designing are studied and main affecting factors on bonding strength characteristics are analyzed.
本文通过对铝板件进行冲压连接实验,研究了这种冲压连接技术的机理和冲压模具设计,并重点分析了影响连接强度特性的主要因素。
3) connecting strength
连接强度
1.
Analysis of effect of thread parameter tolerances on connecting strength of tubing threads;
螺纹参数公差对油管螺纹连接强度的影响分析
2.
The scope of the work included connecting strength,tightness and fatigue strength of the expansionjoints.
研究范围包括胀接结构的连接强度，密封即耐压性能，疲劳强度等。
4) connection strength
连接强度
1.
Research on the knurling connection strength of hollow assembled camshaft
中空组合式凸轮轴滚花连接强度研究
2.
The effect of expanding degree on the connection strength of hydraulically expanded and mechanically expanded tube-to-tubesheet joints of heat exchangers was investigated by experiments based on the specimens with seven triangularly arranged holes perforated in tubesheets.
采用按三角形排列的7管孔试件,进行了胀紧程度对换热器液压胀接和机械胀接接头连接强度影响的试验研究。
3.
The major factors re sponsible for high connection strength are analyzed,and their coun-termeasure is put forward.
所求得的推力以及抗拉力和实验值比较接近,结果表明:该管道连接方法连接强度高,连接可靠。
5) joint strength
连接强度
1.
Si_3N_4 ceramic was brazed with Ti40Zr25Ni15Cu20 amorphous filler metal, the effect of brazing processing parameters on interfacial microstructure and joint strength was discussed.
采用Ti40Zr25Ni15Cu20非晶钎料钎焊Si3N4陶瓷,研究钎焊工艺参数对界面反应层和接头连接强度的影响。
2.
The status quo and progress in reaction wetting, reactive brazer, interfacial reaction, joint strength and partial transient liquid-phase bonding were reviewed in this paper.
本文综述了近年来在反应浸润、活性钎料、界面反应、连接强度和部分瞬间液相连接方面的研究现状和进展 ,指出了有待进一步研究的问题。
3.
are described and the joint strength of them by electroplating is determined.
研究表明,基体材料的表面处理、镀接材料与电解液的选取对连接强度有着明显的影响。
6) joining strength
连接强度
1.
The results show that brazing temperature and holding time have an important influence on joining strength, and the highest strength value (289 MPa) was achieved at the brazing temperature of 1 373 K for 10 minutes.
结果表明:钎焊温度和时间对连接强度有重要影响;在1373K,10min的连接条件下,Si3N4/Si3N4连接强度达到最大值289MPa。
2.
It was shown that the joining strength was ve ry low(only11MPa)when they were brazed directly.
结果表明,两者直接钎焊时连接强度较低,仅为11MPa;插入中间层Ni可有效减缓接头中V的残余应力,提高连接强度。
3.
The effects of the braze metal composition, and the procedure variables such as the brazing temperature and the brazing time on joining strength are investigated.
结果表明 :钎料成分、钎焊工艺参数对连接强度均有重要影响。
补充资料：椐椐强强
1.相随貌。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条