1) Single-point preview
单点预瞄
2) multipoint preview
多点预瞄
1.
A multipoint preview control algorithm was designed for vehicle active suspension systems, in which Pade approximation technique was used to represent the multipoint preview information.
设计了一种多点预瞄控制算法,并将该算法应用于具有主动悬架系统的二分之一车辆模型中。
3) Preview
[英]['pri:vju:] [美]['pri'vju]
预瞄
1.
Driver Model for Single Track Vehicle Based on Single Point Preview Optimal Curvature Model;
基于单点预瞄最优曲率模型的单轨车辆驾驶员模型
4) preview control
预瞄控制
1.
Based on the wheelbase preview control,a preview control method for MRF semi-suspension vehicle is present,and also considering the relationship between the control current and output damping force of the MRF(magneto-rheological fluid) damper.
在综合利用磁流变减振器控制电流与输出阻尼力的关系、以及轴距预瞄控制技术的基础上,提出汽车磁流变半主动悬架预瞄控制方法,通过理论分析和计算机仿真,研究在不同行驶速度下汽车磁流变半主动悬架动态性能,实验表明,该法具有提高悬架系统的控制性能,使悬架承受的冲击响应小、振动强度低和汽车行驶平顺性好等特点。
2.
With the behaviorbased path planning and intelligent preview controlling, a basic vision based navigation system was created and implemented on our autonomous robot test bed ATRV2.
根据结构化道路环境的特点提出了一种将边沿检测和道路环境知识相结合的机器视觉算法,并结合基于行为响应的路径规划方法和智能预瞄控制方法,实现了一套基本的机器人视觉导航系统。
3.
By imitating the preview driving behavior of human, an effective intelligent preview control method for mobile robot road following was developed.
本文首先介绍了移动机器人的基本硬件组成 ,然后模仿人工预瞄驾驶行为 ,提出了一种移动机器人路径跟踪的智能预瞄控制方法 ,并介绍了智能预瞄控制器的原理、结构及其设计过程 。
5) preview distance
预瞄距离
6) Preview follower
预瞄跟随
1.
Application of preview follower theory and driver model in the research of vehicle intelligent handling;
预瞄跟随理论和驾驶员模型在汽车智能驾驶研究中的应用
补充资料:闭式单点、双点压力机
| |||||||
主要参数内容 | 国际先进 | 国内先进 | 国内一般 | 国内落后 | 评定方法及说明 | ||
(一)加工精度 | 参照GB10924-89、GB10933-89、JB5200-91 | ||||||
1、滑块下平面对工作台上平面的平行度(mm) | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.02+0.10/100×滑块下平面的被测长度 | |||||||
2、滑块行程对工作台上平面的垂直度 | 30%精度储备 | 20%精度储备 | 达到规定值 | 大于规定值 | |||
0.05+0.02/100×滑块行程长度 | |||||||
(二)结构性能 | |||||||
1、离合器、制动器接通率,当滑块行程次数≤16次/分时为70%,≤25次/分时为60%,≤45次/分时为50% | 大于规定值10% | 大于规定值 | 达到规定值 | 达不到规定值 | |||
2、液压超负荷保险装置、微调装置、吨位指示器 | 全部具有 | 全部具有 | 部分具有 | 没有 | |||
(三)噪声dB(A) | |||||||
1、公称力≤400kN | ≤85 | ≤87 | ≤88 | >88 | |||
2、公称力>400kN | ≤87 | ≤88 | ≤90 | >90 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条