1) internal and external prestress
![点击朗读](/dictall/images/read.gif)
体内外预应力
2) internal and external tendon
![点击朗读](/dictall/images/read.gif)
体内外预应力索
3) external prestressing in tubes
![点击朗读](/dictall/images/read.gif)
体外管内预应力
1.
The project of Jiangsu science history culture center is external prestressing in tubes of cantilever beam structure.
江苏省科学历史文化中心工程体外管内预应力吊拉多层大悬挑梁结构,有别于传统的施工方法,优点有:通过张拉拉索,在结构中建立有效、合理预应力,以平衡部分使用荷载,为悬挑结构提供弹性支点,控制结构变形,提高结构刚度,外形美观,使结构具有空间感;但该结构受力分析复杂,施工存在一定的难度,张拉不当可能会导致挑梁变形过大,应力超标,进而在挑梁根部产生裂缝。
4) internal and external prestressing
![点击朗读](/dictall/images/read.gif)
体内与体外预应力
5) External prestressing
![点击朗读](/dictall/images/read.gif)
体外预应力
1.
The technology of external prestressing and the application and development in bridge;
![点击朗读](/dictall/images/read.gif)
体外预应力技术及其在桥梁中的应用与发展
2.
Inverted arch deflection analysis for reinforced concrete beams strengthened by external prestressing tendons;
体外预应力加固混凝土简支梁的反拱挠度分析
3.
Experimental research on the RC two-way slabs strengthened with the one-way external prestressing method;
体外预应力加固混凝土双向板的试验研究
6) external prestress
![点击朗读](/dictall/images/read.gif)
体外预应力
1.
Study on external prestressed concrete beam with carbon fiber reinforced polymer;
![点击朗读](/dictall/images/read.gif)
碳纤维筋体外预应力混凝土梁的研究
2.
Equipollent load calculation of external prestressed continuous girder;
![点击朗读](/dictall/images/read.gif)
体外预应力连续梁的等效荷载计算
3.
The application of external prestressed technology in highway engineering;
![点击朗读](/dictall/images/read.gif)
论体外预应力技术在公路工程中的应用
补充资料:弹塑性岩体内竖井地压理论
弹塑性岩体内竖井地压理论
ground pressure around shaft in elastic-plastic rock
tonsux一ng yant一ne一shuJ一ngd一yol一}un弹塑性岩体内竖井地压理论(ground pres-sure around shaft in elastie一plastie roek)在表土或软岩中掘进竖井时,若岩体只产生弹性变形,岩体是稳定的,不必计算地压。只有在产生塑性及流变变形时,才需要计算地压;竖井各水平截面上地压不等。按轴对称条件求出竖井周边位移,再求出支护位移公式,将它们联立求解,即可得到竖井地压。也可用图解法找到两条位移与应力关系曲线的交点,该点的纵坐标值即为竖井地压(见图)竖井围岩周边位移公式为: “止 U 竖井变形地压计算图 1围岩位移曲线;z支护特性曲线 a(p。s、n,,+。eos叭)厂(尸。+。.eot,t川一sin,.门导 ZG,匕P。+cicot笋,J式中“。为竖井围岩周边位移,m;a为竖井掘进半径,m;P0为原岩水平应力,重力场条件下,P0一六yI1,MPa;c,为第i层岩石粘结力,MPa;尸b为支护抗力,等于围岩作用在支护结构上的径向压力,但作用方向相反,MPa;笋,为第i层岩石内摩擦角;G.为第!层岩石剪切弹性模量;MPa。 竖井筒形支护特性方程为: l一群2厂bZ+a,尸1。, z,‘一二六舟}头‘-共一一IP,b EL右2一aZx一尸J“”式中u。为支护外半径表面的径向位移,支护与围岩密贴的情况下,“,一“、;E及产分别为支护材料的弹性模量及泊桑比;“为支护内半径,m;b为支护外半径,m;尸二为竖井变形地压,尸。一尸b,MPa。 (高磊)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条