1) exhaust smoke valve
排烟阀
2) smoke fire damper
排烟防火阀
1.
This paper analyses the problems about the control of the mechanical smoke extraction system,and discusses the problem about smoke fire dampers and smoke exhausting fans.
分析了机械排烟系统的有关控制问题,对排烟风机和排烟防火阀的有关问题进行了探讨,提出了优化机械排烟系统的一些措施。
3) smoke exhaust
排烟
1.
Comparison of different methods of ventilation and smoke exhaust in underground parkings;
地下汽车库通风排烟不同方式的比较
2.
Analysis on ventilation and smoke exhaust for civil air defense underground garages;
浅析人防地下车库通风与排烟设计
3.
Discusses on ventilation and smoke exhaust system design for basement of highrise civil buildings;
高层民用建筑地下室通风排烟系统设计探讨
4) flue gas
排烟
1.
In the article we not only analysed the theory of flue gas condensation, but also studied the theory that the various parts of flue gas was absorbed and purified in the course of the flue-gas condensation.
烟气冷凝能够降低排烟中有害物质的浓度 ,减轻锅炉排烟对大气的污染 ,有利于环
2.
Aimed at the fact that the wall temperature of heat exchanger is lower than the dew point of flue gas, the thermal energy utilization system for flue gas of positive draft gas boiler is proposed.
针对烟气换热器壁面温度会低于排烟露点的情况,提出了正压通风燃气锅炉排烟热能利用系统。
5) exhaust smoke
排烟
1.
The discussion on the problems of ventilation and exhaust smoke in high-rise building underground garage;
高层建筑地下汽车库通风和排烟问题的探讨
2.
Study on utilizing the remains of heat of the exhaust smoke from boilers used in ships;
船用锅炉排烟余热利用的研究
3.
Obtains the relationship curves of smoke temperature with the height of model atrium by smoke tests under natural ventilation,supply air in upper zone,exhaust smoke in lower zone and combined with upper supply and lower exhaust conditions.
在模型中庭内进行了发烟实验,得到了在自然状态、上送风、下排烟和上送下排状态下烟气温度随模型中庭高度的变化曲线。
6) Smoke extraction
排烟
1.
Exhaust ventilation and smoke extraction design for underground garages;
地下汽车库的排风与排烟系统设计
2.
Design of ventilating and smoke extraction system in underground garage of Huli water amusement park;
湖里水上乐园地下汽车库通风排烟设计
3.
Design of ventilation and smoke extraction system for civil air defense underground garages;
人防地下车库通风与排烟系统设计
补充资料:溢流阀、顺序阀、减压阀的比较
溢流阀 | 减压阀 | 顺序阀 | ||
控制油路的特点 | 通过调整弹簧的压力控制进油路的压力,保证进口压力恒定,p2=0 | 通过调整弹簧的压力控制出油口的压力,保证出口压力p2稳定 | 直控式-通过调定调压弹簧的压力控制进油路压力;夜控式-由单独油路控制压力 | |
出油口情况 | 出油口与油箱相连 | 出油口与减压回路相连 | 出油口与工作回路相连 | |
泄漏形式 | 内泄式 | 外泄式 | 内泄式 | |
进油口状态及压力值 | 常态 | 常闭(原始状态) | 常开(原始状态) | 常闭(原始状态) |
工作状态 | 进出油口相通,进油口压力为调整压力 | 进油口压力低于出油口压力,出油口压力稳定在调定值上 | 进出油口相通,进油口压力允许继续升高 | |
联接方式 | 并联 | 串联 | 实现顺序动作式串联作卸荷阀用时并联 | |
功用 | 定压、溢流或安全作用限压、稳压、保压 | 减压、稳压 | 不控制系统的压力,只利用系统的压力变化控制油路的通断 | |
进油腔压力p1控制阀芯移动 | 出油腔压力p2控制阀芯移动 | 进油腔压力p1控制阀芯移动 |
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条