1) big-small hole
大小孔
1.
In this paper,the structure characters of Connecting Rod is analyzed,the manufacture crafts of Connecting Rod s important section are described,and some factors which could influence manufacture quality of the Connecting Rod s big-small holes are analyzed,so that some proposals to improve manufacture quality of Connecting Rod are given.
本文就连杆的结构设计特点进行了分析,对其关键部位的加工工艺进行了阐述,对影响连杆大小孔加工质量的一些因素进行了分析,从而得出提高连杆的加工质量应注意的几个问题。
2) pore size
孔隙大小
1.
The results show that the porosity of excessive-ceramic areas in two coatings are similar and it is the greatest at the interface which is less than 6%,the probability distributions of pore size in two coatings are resemble,pores of diameters from 1um to 10um are the most w.
利用定量金相技术对两种涂层富陶瓷区域不同位置的孔隙率、孔隙大小和形态进行了定量分析。
3) pore size
孔径大小
1.
Effect of support pore size on integrity of Al_2O_3 micro-filtration membranes;
支撑体孔径大小对Al_2O_3微滤膜完整性的影响
2.
A method based on the surface force pore flow model to characterize the pore size and pore size distribution of polymer porous filtration membranes was reviewed.
综述了一种建立在表面作用力孔流通模型基础上计算高分子多孔滤过膜孔径大小及分布的方法。
3.
The results demonstrate that the average pore size of nature.
5nm的沉积物体系中甲烷水合物的分解平衡温度和压力条件(即相平衡)进行了测定,结果表明,近自然沉积物的平均孔径大小会影响甲烷水合物的相平衡条件。
4) barrel hole size
孔眼大小
1.
Influences of cathodic current density, barrel rotative speed and barrel hole size on nickel electrodeposition performance including electrodeposition rate of nickel, cathodic current effciency and bath throwing power are discussed.
提出滚镀瓦特镍的工艺配方和操作条件，讨论了阴极电流密度、滚筒转速、孔眼大小等对镍电沉积性能如镍沉积速度、阴极电流效率、镀液分散能力等的影响。
5) Pore throat size
孔喉大小
6) pupil size
瞳孔大小
1.
After instillation of tropicamide 10g/L,pupil size at different time points was measured and the time to reach a pupil diameter of 6mm was recorded before surgery and at 1 month after surgery.
方法:对34例(64眼)接受LASIK治疗的近视眼患者,于术前和术后1mo测量并比较10g/L托吡卡胺扩瞳后5,10,15,20min以及25min时的瞳孔大小,并记录瞳孔达到6mm大小所需时间。
2.
Pupil size,anterior chamber depth and posterior corneal surface altitude were measured with Orbcan-Ⅱanterior segment analyzer before and 1 day and 1 month after LASIK.
目的探讨准分子激光原位角膜磨镶术(laser in situ keratom ileusis,LASIK)对瞳孔大小及前房深度的影响。
补充资料：第二孔(继发孔)型缺损
第二孔(继发孔)型缺损
ostium secondary defect
是心房间隔在形成上发生障碍，一般缺损较大，多在卵圆孔附近称第二孔(继发孔)型缺损。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条