1) Plate-fin recuperator
板翅式回热器
1.
Investigations on heat transfer performance of a plate-fin recuperator;
板翅式回热器传热性能研究
2.
Numerical simulation and experimental study on plate-fin recuperator in microturbine
板翅式回热器试验与数值模拟研究
3.
A lumped parameter model was proposed to research dynamic performances of plate-fin recuperator in high-temperature gas-cooled reactor with direct helium turbine cycle(HTGR-GT).
针对高温气冷堆直接氦气透平循环中的板翅式回热器,研究提出一仅考虑回热器芯部热容的集总参数模型,即无限大芯部热容的集总参数模型,并利用四阶龙格-库塔方法求解该模型,求解过程中考虑温度对气体物性的影响。
2) Plate-finned heat recovery equipment
板翅式热回收器
3) Plate-fin heat exchanger
板翅式换热器
1.
Dynamic performance simulation of plate-fin heat exchangers in small scale MRC-LNG plant;
小型MRC天然气液化装置中板翅式换热器动态特性仿真研究
2.
Research progress of plate-fin heat exchanger in china;
板翅式换热器的研究进展
3.
Three dimensional numerical simulation on surface performance of a plate-fin heat exchanger.;
板翅式换热器翅片表面性能的三维数值模拟
4) plate-fin heat exchanger
铝板翅式换热器
1.
Experimental Investigation of surface performance of aluminum fins on plate-fin heat exchanger;
铝板翅式换热器翅片表面性能的试验研究
5) Plate Fin Heat Exchanger
板翅式换热器
1.
Efficiency study of plate fin heat exchanger with principle of field synergy;
场协同下板翅式换热器效率的研究
2.
A technical development of developing, designing and manufacturing of plate fin heat exchanger for petroleum and chemical engineering are described.
阐述石油化工板翅式换热器的开发设计和制造技术进展。
3.
The flow nonumiformity and effects of different distributior s configuration on flow distribution performance in plate fin heat exchanger was studied.
分析了不同结构导流片对板翅式换热器内部物流分配不均匀性的影响 ,通过改变导流片的内部结构 ,对其导流性能进行了研究 。
6) plate-fin heat exchangers
板翅式换热器
1.
Based on the study of the flow maldistribution in (plate-fin) heat exchanger,the effect of staggered(perforated) plate header configuration on outlet flow and heat transfer in plate-fin heat exchangers was experimentally studied.
在对板翅式换热器内部物流分配研究的基础上,研究了错排孔板型结构封头对板翅式换热器出口流动与换热的影响。
2.
This general solution can be used to analyze the dynamic response of plate-fin heat exchangers by simplifying the dynamic behavior of fins with Pingaud model.
应用Pingaud模型对板翅式换热器翅片的动态特性进行简化,从而使该通用解可用来求解多股流板翅式换热器的动态特性。
补充资料：板翅式热交换器（platewingheatexchanger）
板翅式热交换器（platewingheatexchanger）
铝制板翅式热交换器是在数层平金属板之间紧密地放置波纹状的金属导热翅片，并在每一层的四周加上封条，于温度近600℃的盐溶液炉中整体铅焊而成。翅片的主要作用是强化传热，也有增强两金属板强度的作用，在这种热交换器中相邻两通道之间的热交换，一部分通过平板传递热量，但绝大部分热量是通过波纹翅中传递的，因为平板之间均有波纹翅片，因而大大增加了传热面积，所以它的单位体积内的传热面积比一般管式热交换器大10倍以上，达到4000～5000m2/m3。通过各通道之间的不同组合，可得到逆流、错流等形式的热交换器。它具有单位体积传热面积大、传热效率高、流体阻力小、热容量小、结构紧凑及同时允许几种介质进行热交换等优点。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条