说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 肋台台背
1)  back of ribbed slab
肋台台背
2)  back of abutment
台背
1.
Study on the kind of filling and disposing the back of abutment;
台背处理及回填类型研讨
2.
This article,considering the construction technique and quality control of the backfilling of the back of abutment in the seventh phase of Qinglai Expressway,gives some suggestions,which will provide valuable references for later backfilling construction.
文章结合青莱高速公路七合同段台背回填施工工艺及质量控制,并根据实际施工情况提出了一些建议,为以后公路台背回填的施工提供了宝贵经验。
3)  retailing backwall
台背
1.
The paper introduced the construction technology of liquid flyash pouring retailing backwall in order to assure refill quality of retailing backwall,protect retailing backwall depression or jumping.
介绍了为保证台背回填质量,防止台背沉陷或跳车,在地形受限制的地方,采用液态粉煤灰灌注台背的施工工艺,对这项施工工艺的方法、步骤和注意事项进行了详细的阐述。
2.
For assuring the fill quality of structure retailing backwall for Taichang Expressway,the paper proposed relative control measures for reference.
桥头跳车已是公路建设的质量通病,根治难度很大,为确保太长高速公路构造物台背的回填质量,太长公司制定了相关技术质量控制措施,有效地指导了桥涵构造物台背的施工。
3.
The paper mainly introduced the importance of the grouting strengthening for expressway bridge & culvert retailing backwall.
重视台背注浆,对桥涵构造物两侧台背填方实施注浆加固,其目的是增大台背填方密实度,减少台背沉降量,缩小台背与桥涵构造物的差异沉降,消除台背下沉引起行车的不良后果,从而避免了桥头跳车现象,确保台背工程质量。
4)  abutment [英][ə'bʌtmənt]  [美][ə'bʌtmənt]
台背
1.
On application of hydraulic high-speed compaction technique in abutment backfill in structure
高速液压夯实技术在结构物台背回填中的应用
2.
Discussion on the grouting strengthening technology of bridge and culverts abutment steel flora tube
桥涵台背钢花管注浆加固处理技术探讨
5)  abutment back
桥台台背
1.
And some measurements are recommended to improve drainage of abutment back.
根据调查发现,水是引起桥台引道沉陷的主要原因,在分析桥台台背回填材料的性质对排水能力影响的基础上,借助于室内桥头引道排水模型(BADM)试验,对13种排水模型进行试验研究,可发现三种排水模型的排水效果最好,并有助于提出改善桥台台背排水能力的有效措施。
6)  ring stiffened truncated conical shell
环肋锥台
1.
Load carrying capacity of a ring stiffened truncated conical shell which is made from a high strength steel has been experimentally and theoretically examined.
采用规则法、解析法和有限元法对环肋锥台的承压能力进行了理论分析与计算,并利用模型实测结果评定了这些方法的精度情况,指出了由高强钢制造的环肋圆锥壳的破坏主要是结构薄弱处壳体纵横截面上的中面应力所造成,规则法计算结果虽偏安全,但过于保守。
补充资料:背对背
背靠背。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条