说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 轴承芯轴
1)  bearing core shaft
轴承芯轴
1.
The fractured surface of bearing core shaft of a certain water pump assembly was investigated by means of macroscopic,microscopic and section fractography.
通过对水泵总成中发生断裂的轴承芯轴进行断口的宏观分析、微观分析和剖面分析,及其中各组件的相对位置、表面痕迹和宏观形貌的分析和讨论,分析失效原因,提出改进建议。
2)  bearing siphon wool
轴承油芯
3)  core [英][kɔ:(r)]  [美][kɔr]
芯轴
1.
It is considered that the defects of vacuum pugged body are attributed to improper mud hardness,pugmill cylinder shape,core connection and parameters of electric preheating.
结合生产实际,对造成110kV SF6瓷套真空细练泥段变形和开裂的原因进行了分析,认为粗练泥段的硬度、工艺筒和芯轴的连接方式及电阴干工艺是造成真空细练泥段缺陷的主要原因。
4)  core shaft
芯轴
1.
Mainly analyzed the influence of the core shaft friction coefficient to spindle-foot forward hollow extruding to 20 steels forming.
主要对锭脚空心正挤过程中芯轴摩擦系数对20钢成形的影响进行有限元分析。
2.
This paper introduces the technology of repairing ESS380 roller-ring core shaft.
本文论述了ESS380辊环芯轴的修复工艺及经济效
5)  spindle [英]['spɪndl]  [美]['spɪndḷ]
芯轴
1.
In order to avoid the problems such as liable heat generation,leakage of oil,abrasion and deform of the spindle on the common cot sleeves,as well as the other problems such as maintenance and energy consumption,introduction is given to the new cot sleeve of free lubrication.
为了解决常规并条胶辊套筒存在的易发热、易漏油,芯轴易弯曲磨损以及保养、能耗等问题,介绍了新型免加油并条胶辊套筒的性能特点并以实际生产数据进行对比;说明实际使用该新型并条胶辊套筒综合效果好,具有省工省时、降低消耗、质量稳定、使用寿命长、总投资少等优点。
6)  mandrel [英]['mændrəl]  [美]['mændrəl]
芯轴
1.
Design of hot rolling plunger drum remodeling and mandrel;
一种双斜面芯轴的斜楔柱塞式卷筒的设计
2.
Mathematic calculation approach of minimum bending radius of mandrel based on Matlab
基于Matlab的芯轴最小弯曲半径计算
补充资料:K311八轴挤芯机操作规程
1、遵守铸造设备通用操作规程。
2、检查三角皮带的松紧度与磨损情整,如过紧、过松,或磨损严重,应予调况或更换。
3、先点动试车,然后空运转2-3分钟,检查传动系统(电动机、减速器)以及压杆与塞杆的运动是否正常,确认一切正常后,方可进行生产。
4、工作后,清理设备时,要特别清理料槽中和套筒里的积砂。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条