说明:双击或选中下面任意单词,将显示该词的音标、读音、翻译等;选中中文或多个词,将显示翻译。
您的位置:首页 -> 词典 -> 球孔加工
1)  spherical-hole processing
球孔加工
2)  Drilling [英]['driliŋ]  [美]['drɪlɪŋ]
孔加工
1.
Usually, afterprocessing is necessary for the lightweight composite components before assembling, such as drilling, cutting, slotting, etc.
轻质复合构件成型后,根据装配要求需要进行二次加工,如钻孔、切边、开槽等,尤其需要大量的孔加工。
2.
Drilling process of the ceramic composite component(ceramics/FRP/aluminum alloy),as an example of ceramics/FRP laminate composite component,was studied intensively.
以陶瓷复合构件(陶瓷/玻璃钢/铝合金层叠)为例,对陶瓷/FRP层叠复合构件的孔加工工艺进行深入研究。
3.
Experimental Investigation on Drilling Kevlar Fiber Reinforced Composite with Sintered Diamond Bits;
以正交铺设的Kevlar层合板为对象,采用烧结金刚石钻头对其孔加工进行试验研究。
3)  deep-hole machining
深孔加工
1.
In view of some of the difficult points for machining the hanging pup joints used in directional wells, a special technology for deep-hole machining is developed.
针对650型定向井悬挂短节的加工难点,研究了特殊的深孔加工工艺。
2.
To rebuild normal turner into machine tool of deep-hole machining based on programmable logic controller (PLC) and AC frequency control technology, electrical control system of high performance machine tool was designed, which could realize self-turning.
基于可编程控制器(PLC)和交流变频调速技术把普通车床改造成深孔加工机床,设计了能实现自主切削的高性能机床电气控制系统,系统主要由PLC、变频器、触摸屏、步进电机及其配套的驱动器组成。
4)  Hole machining
孔加工
5)  Arc hole
曲孔加工
6)  microdrilling
微孔加工
1.
Study on laser microdrilling nearby the last threshold;
激光阈值附近微孔加工方法的研究
补充资料:普通免疫球蛋白 ,人血丙种球蛋白,丙种球蛋白
药物名称:丙种球蛋白

英文名:γ-Globulin

别名: 免疫血清球蛋白;普通免疫球蛋白 ,人血丙种球蛋白,丙种球蛋白
外文名:γ-Globulin
适应症: 含有健康人群血清所具有的各种抗体,因而有增强机体抵抗力以预防感染的作用。主要用于免疫缺陷病以及传染性肝炎、麻疹、水痘、腮腺炎、带状皰疹等病毒感染和细菌感染的防治,也可用于哮喘、过敏性鼻炎、湿疹等内源性过敏性疾病。
用量用法:
肌注:每次2~5ml,3周1次,用于内源性过敏性疾病,每次10ml(含量10%者),3周内注射2次。胎盘球蛋白每次6~9ml。
注意事项:
1.按球蛋白来源可分为两种,一为健康人静脉血来源的丙种球蛋白制剂,按蛋白质含量有10%、16%、16.5%等数种(国内制品浓度在10%以上),其中丙种球蛋白占95%以上。另一种为胎盘血来源的丙种球蛋白(人胎盘血丙种球蛋白),即胎盘球蛋白,含蛋白质5%,其中丙种球蛋白占90%以上。胎盘球蛋白因丙种球蛋白含量以及纯度均较低,其用量应相应增大。 2.除专供静注用的制剂外,一般制剂不可静注。 3.注射大量时,可见局部疼痛和暂时性体温升高。
注:参见:“丙种球蛋白注射液”.



类别:免疫增强剂(免疫反应调节剂)
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条