1) inner cooling water system
内冷水系统
1.
In view of the problems of inner cooling water,such as low pH value and excessive mass concentration ρ(Cu2+) of copper ion,in the double-water inner-cooling turbogenerators of 4 units in Yunfu Power Plant,the 125 MW Unit 2 is taken as an example to describe the modification of the generator inner cooling water system.
云浮发电厂4台机组双水内冷汽轮发电机均存在内冷水pH值偏低、铜离子质量浓度ρ(Cu2+)过大的问题,以2号机组(125MW)为例,介绍了发电机内冷水系统技术改造的过程。
2) internal bubble cooling system
内冷系统
1.
The melt strength of mLLDPE was compared with that of LDPE,and the effect of temperature on the melt strength of mLLDPE was analysed experimentally,and the reason of the internal bubble cooling system introduced in mLLDPE blowing was explained.
从实验上比较了mLLDPE和LDPE的熔体强度,分析了温度对mLLDPE熔体强度的影响,说明了在mLLDPE的吹膜引入内冷系统的原因。
3) generator inner cooling water system
发电机内冷却水系统
4) chilled water system
冷水系统
1.
Dynamic simulation of VWV chilled water system and its control system;
变流量冷水系统及其控制系统的动态仿真
2.
Analyses the large temperature difference chilled water systems.
结果表明 :当冷水机组冷水初温等于或大于 7℃时 ,1 0℃温差与 5℃温差时冷水机组的能耗基本相同 ,而蒸发器压降明显减小 ;冷水系统采用 1 0℃温差较 5℃温差冷水量减少一半 ,水泵能耗减少 ,水系统一次投资减少 ;即使空调机组一次投资略有增加 ,空调水系统的一次投资可减少 5%左右 ,空调水系统运行费用减少 30 %左右。
5) water cooling system
水冷系统
1.
Automation switch of pump motor in the water cooling system by PLC;
PLC实现水冷系统中水泵电机的自动投切
2.
Some important parameters about the water cooling system of high current RFQ cavities, such as the heat transfer coefficiency and the optimized temperature of the cooling water, were obtained.
利用有限元计算软件ANSYS分析了热效应对加速腔共振频率的影响,计算了RFQ腔体与热效应有关的参数,如水冷系统的冷却水温度、热交换系数等。
3.
Maintenance and reconstruction of water cooling system for VF-320 X-ray fluorescence spectrometer were discussed in this paper.
针对X射线荧光光谱仪的水冷系统内循环水压下降的问题,提出了在原冷却系统的泵前串接一个不锈钢泵的方法。
6) water-cooling system
水冷系统
1.
This article provides a comparison between the improving water-cooling system and the old cooling system fromthe economical and practical aspect, and it further specifies the design, steps of the water-cooling system by using fire cister
本文从经济、实用角度对改进型水冷系统和以往冷却系统进行比较,并从设计角度列出了利用消防水池作冷却水系统的设计步骤。
2.
According 2124 aluminium alloy craftwork specialty and constriction modulus,combining specification,ensuring design\'s project of 2124 alloy 255 mm×1 500 mm ingot specification mould、water-cooling system、base and filler.
根据2124铝合金工艺特性和收缩系数,结合铸锭的规格,确定了铸造2124铝合金255 mm×1500 mm规格铸锭的结晶器、水冷系统、底座及漏斗的设计方案。
补充资料：人的内分泌系统人体主要内分泌腺
李瑞端绘
[图]
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条