2) rectangular plate elastical bending
![点击朗读](/dictall/images/read.gif)
薄板弹性弯曲
3) bending of elastic plate
![点击朗读](/dictall/images/read.gif)
弹性板弯曲
4) thin plate bending
![点击朗读](/dictall/images/read.gif)
薄板弯曲
1.
Element-free-method MLS derivatives based on orthogonal basic functions and its application to thin plate bending;
基于正交基函数的薄板弯曲无单元法MLS导函数及其应用
2.
Meshless solution for thin plate bending problems;
![点击朗读](/dictall/images/read.gif)
弹性薄板弯曲问题的无网格解法
3.
Based on thin plate bending theory of elasticity theory, a model of space layer was applied to solve the problem about ground surface movements due to underground rock excavation.
以弹性薄板弯曲理论为基础 ,对层状矿体开采引起的地表及岩体移动问题 ,引入层状模型进行描述 ,得到了水平及倾斜矿体开采的地表移动空间解析式、计算程序 ,并用于地表移动预计 ,现场实测结果与计算结果对比 ,效果较好。
5) bending plate
![点击朗读](/dictall/images/read.gif)
弯曲薄板
1.
Damage detection of bending plate based on modal variable ratio of strain;
![点击朗读](/dictall/images/read.gif)
基于应变模态变化率的弯曲薄板结构损伤研究
2.
Using the characteristic of the regular curve boundary for a bending plate in engineering,the analytic integral formulae of assistant states in boundary element method(BEM) with the linear element for a Kirchhoff circular plate are introduced and the systematic equation of BEM is established in this paper.
利用一般弯曲薄板边界为规则曲线的特点,对工程常用的圆形弯曲薄板,采用线性单元,导出K irchhoff圆板各辅助态的边界积分解析表达式,建立问题的边界元法系统方程,从而使薄板的边界元分析完全避免通常使用的高斯积分,明显提高计算精度。
6) plate bending
![点击朗读](/dictall/images/read.gif)
薄板弯曲
1.
Application of bending moment distribution and carryover limit formula to plate bending problems;
弯矩分配传递极限公式在薄板弯曲问题中的应用
2.
A parallelogram oblique element model is developed in the Finite Element Method of Lines (FEMOL) for the solutions of oblique plate bending problems.
计算实践表明,仅用很少数量的斜单元网格就可以得斜型薄板弯曲问题高精度的解答。
补充资料:弯曲工艺的概念及弯曲件
1.弯曲工艺:是根据零件形状的需要,通过模具和压力机把毛坯弯成一定角度,一定形状工件的冲压工艺方法。
2.弯曲成形工艺在工业生产中的应用:应用相当广泛,如汽车上很多履盖件,小汽车的柜架构件,摩托车上把柄,脚支架,单车上的支架构件,把柄,小的如门扣,夹子(铁夹)等。
弯曲的基本原理:以V形板料弯曲件的弯曲变形为例进行说明。其过程为:
1. 凸模运动接触板料(毛坯)由于凸,凹模不同的接触点力作用而产生弯矩, 在弯矩作用下发生弹性变形,产生弯曲。
2. 随着凸模继续下行,毛坯与凹模表面逐渐靠近接触,使弯曲半径及弯曲力臂均随之减少,毛坯与凹模接触点由凹模两肩移到凹模两斜面上。(塑变开始阶段)。
3.随着凸模的继续下行,毛坯两端接触凸模斜面开始弯曲。(回弯曲阶段)。
4.压平阶段,随着凸凹模间的间隙不断变小,板料在凸凹模间被压平。
5. 校正阶段,当行程终了,对板料进行校正,使其圆角直边与凸模全部贴合而成所需的形状。
弯曲变形的特点: 弯曲变形的特点是:板料在弯曲变形区内的曲率发生变化,即
弯 曲半径发生变化。从弯曲断面可划分为三个区:拉伸区、压缩区和中性层。
说明:补充资料仅用于学习参考,请勿用于其它任何用途。
参考词条