1) minimum transmission angle
最小传动角
1.
Position analysis of minimum transmission angle of idle stroke in crank-rocker mechanism;
曲柄摇杆机构慢行程最小传动角位置分析
2.
Analytical method for designing crank-rocker mechanism according to minimum transmission angle;
按最小传动角设计曲柄摇杆机构的解析方法
3.
This paper is disscussing a new method which is used to determine the position and dimension of minimum transmission angle of plane Crank-and-Rocker mechanism with Time Ration(k=1&k≠1).
阐述了确定行程速比系数和的平面曲柄摇杆机构最小传动角位置和大小的新方法。
2) minimum driving angle
最小传动角
1.
According to its equivalent mechanism—crank rocker mechanism, driving performance and minimum driving angle position of movable tooth is analyzed.
利用摆动活齿传动等效机构,分析其传动性能和最小传动角的位置。
2.
Given the stroke speed ratio factor K of the quadric crank mechanism and the position of the two poles of the actuating driven member, using the minimum driving angle as the objective, the type and size of the quadric crank mechanism are determined with optimistic technology.
已知曲柄四杆机构的行程速比系数 K及执行从动件动点的两极限位置 ,采用最优化技术 ,以机构最小传动角最大作为寻优目标函数 ,确定曲柄四杆的类型及其尺寸。
3.
With the assistance of computer coded program, this paper, by means of geographically analysing crank and rocker mechanism, helps readers to find out a center point, at which the biggest minimum driving angle is.
通过对图解法设计曲柄摇杆机械的几何分析 ,用计算机编程设计找到使机构最小传动角最大的曲柄回转中心 ,达到优化设计机构的目
3) the minimum transmission angle
最小传动角
1.
The article bases on the traditional graphical method,and applies design principle in the references[1],derives the optimizing design methods which under the condition of meeting the fixed slider stroke and the coefficient of variety of stroke velocity,makes the minimum transmission angle of the eccentric crank slider mechanism to maximum(that is the best transmission angle).
在传统图解法的基础上,运用文献[1]中的设计原理,推导出在满足给定的滑块行程和行程速度变化系数的条件下,使偏置曲柄滑块机构的最小传动角达到最大(最佳传动角)的优化设计方法。
4) the maximum of the minimum transmission angle
最小传动角的最大值
6) optimum drive angle
最优传动角
1.
Give a way of designing the plane crank-rocker mechanism by the coefficient of stoke ratio K and optimum drive angle.
将图解法原理与解析手段有机结合,给出一种同时按K和最优传动角设计平面曲柄摇杆机构的方法。
2.
On the premise of satisfying the given rocker angle of oscillation and the coefficient of stoke speed ratio K, the mechanism can make a optimization design with the halp of a computer and conveniently get the Plane crank-rocker mechanism of the optimum drive angle.
在满足给定的摇杆摆角和行程速比系数K的前提下 ,借助计算机进行寻优设计 ,方便地求得具有最优传动角的平面曲柄摇杆机构。
补充资料：最小辐亮度与最小辐照度(见核爆炸火球)
最小辐亮度与最小辐照度(见核爆炸火球)
minimum-brightness and minimum-irradiance
zuixiao fuliangdu yu zuixiaofu乙haodu最小辐亮度与最小辐照度(minimum-brightness and而nimum一irradianee)见核爆炸火球。
说明：补充资料仅用于学习参考，请勿用于其它任何用途。
参考词条